Pelco ExSite Series Explosionproof Positioning System C1300M-C (11/08) 사용자 설명서
C1300M-C (11/08)
39
Quick Programming Guide
(See Page 9)
SET WASHER SEQUENCE
An external washer (not supplied by Pelco) can be used to wash the window of the enclosure.
Accessing AUX 3 or selecting Preset 87 will start the washer sequence.
Accessing AUX 3 or selecting Preset 87 will start the washer sequence.
Use the following steps to program the washer sequence.
1.
Use the joystick to position the cursor beside WIPER and then press Iris Open. The wiper menu
appears on the monitor.
appears on the monitor.
2.
Position the cursor beside SET WASHER SEQUENCE and then press Iris Open.
3.
Edit the preset label:
a.
Use the joystick to position the cursor beside EDIT PRESET LABEL.
b.
Press Iris Open. The following appears on the monitor:
c.
Use the joystick to position the cursor beside a character. Press Iris Open to enter
selection. To clear a character, position the cursor beside BACKSPACE, and then press Iris
Open.
selection. To clear a character, position the cursor beside BACKSPACE, and then press Iris
Open.
d.
When the label is completed, move the cursor to OK. Press Iris Open to return to the Set
Washer Sequence menu.
Washer Sequence menu.
4.
Edit the preset scene:
a.
Use the joystick to position the cursor beside EDIT PRESET SCENE.
b.
Press Iris Open.
c.
Follow the directions displayed on the monitor.
5.
Edit preset camera settings:
a.
Use the joystick to position the cursor beside EDIT CAMERA SETTINGS.
b.
Press Iris Open. The EDIT CAMERA SETTINGS window appears on the monitor. Refer to
the Camera and Advanced Camera Settings sections of this manual to change camera
settings
the Camera and Advanced Camera Settings sections of this manual to change camera
settings
6.
Set the washer time. The washer time programs how long the wiper will be on before it
automatically shuts off. Washer time can be programmed from 4 to 60 seconds.
automatically shuts off. Washer time can be programmed from 4 to 60 seconds.
7.
Program the wiper delay. Wiper delay programs when the wiper will start after the washer
sequence has started. Wiper delay can be programmed from 1 to 30 seconds.
sequence has started. Wiper delay can be programmed from 1 to 30 seconds.
8.
Program the Auto Return to ON or OFF. If the auto return is set to ON the unit will return to the
last operation before the system started the washer sequence. If it is set to OFF, the system
will remain at the preset scene for the washer sequence.
last operation before the system started the washer sequence. If it is set to OFF, the system
will remain at the preset scene for the washer sequence.
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERNS>
<ZONES>
<WINDOW BLANKING>
<ALARMS>
<WIPER>
<AUX>
<CLEAR>
<PASSWORD>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERNS>
<ZONES>
<WINDOW BLANKING>
<ALARMS>
<WIPER>
<AUX>
<CLEAR>
<PASSWORD>
BACK
EXIT
EXIT
UNIT SETTINGS
WIPER CONTROL
AUX 1
WIPER MODE
CONTINUOUS
WIPER DWELL (SECS)
2
WIPER TIME (MINS)
60
<SET WASHER SEQUENCE>
BACK
EXIT
EXIT
WIPER*
* * * PRESET NOT DEFINED * * *
<EDIT PRESET LABEL>
<EDIT PRESET SCENE>
<EDIT CAMERA SETTINGS>
<EDIT PRESET SCENE>
<EDIT CAMERA SETTINGS>
WASHER TIME (SECS)
4
WIPER DELAY (SECS)
1
AUTO RETURN
ON
<CLEAR PRESET>
<CLEAR CAMERA SETTINGS>
<CLEAR CAMERA SETTINGS>
BACK
EXIT
EXIT
REFERENCE INFORMATION
AZIMUTH
AZIMUTH
- -
ELEVATION
- -
ZOOM
- -
CUSTOM CAMERA SETTINGS
- -
SET WASHER SEQUENCE*
* Available only with the wiper models.
EXIT
LANGUAGE
ENGLISH
UNIT INVERSION
OFF
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<UNIT SETTINGS>
<POSITION CALIBRATION>
<DISPLAY SETUP>
<UNIT SETTINGS>
<POSITION CALIBRATION>
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
CYCLE CAMERA POWER
REBOOT SYSTEM
PELCO EXSITE IPSXM
LABEL FOR PRESET WASH
WASH - - - - - - - - - - - -
1234567890 OK
ABCDEFGHIJ
ABCDEFGHIJ
CANCEL
KLMNOPQRST
UVWXYZ.,-/
UVWXYZ.,-/
SPACE
abcdefghij
BACKSPACE
klmnopqrst
uvwxyz#&:”
uvwxyz#&:”