Nissin Di866 사용자 설명서
x4
NOTE
BASIC OPERATION
SETTING THE MODE AND THE FUNCTION
Remove the battery magazine and insert
4 x size AA batteries as shown in the
picture.
4 x size AA batteries as shown in the
picture.
Press the on/off switch. Screen A appears, and the mode A is set.
The pilot lamp blinks red showing the unit is charging.
In a few seconds, the pilot lamp turns green.
The display screen automatically turns off in about 30sec. after the setting
job is terminated.
For a test-flash, press the pilot lamp.
To turn off the flash unit manually, press the on/off switch and hold it for 2
seconds.
The pilot lamp blinks red showing the unit is charging.
In a few seconds, the pilot lamp turns green.
The display screen automatically turns off in about 30sec. after the setting
job is terminated.
For a test-flash, press the pilot lamp.
To turn off the flash unit manually, press the on/off switch and hold it for 2
seconds.
Set Di866 to the camera’s hotshoe and press the on/off switch to power on.
Display screen automatically shows A, the Full Automatic
Mode.
Di866 is now set for the camera’s automatic flash control
system.
Press the on/off switch once again to lock this condition on
your flash. (Press it again to release the lock)
All the jobs required for this mode is completed.
When the pilot lamp turns green, press the shutter button of your camera
halfway to focus the subject.
Shutter speed, aperture and flash mark ( ) are shown in camera’s view finder
and the display panel of the camera.
Press the shutter, and Di866 is fired. The result is immediately shown on the
camera’s LCD monitor.
Flash power is automatically controlled by the camera and the most proper
exposure is obtained on your picture.
When you change the focal length of your camera lens, Di866 responds without
delay and set its light source for the proper illumination angle.
Display screen automatically shows A, the Full Automatic
Mode.
Di866 is now set for the camera’s automatic flash control
system.
Press the on/off switch once again to lock this condition on
your flash. (Press it again to release the lock)
All the jobs required for this mode is completed.
When the pilot lamp turns green, press the shutter button of your camera
halfway to focus the subject.
Shutter speed, aperture and flash mark ( ) are shown in camera’s view finder
and the display panel of the camera.
Press the shutter, and Di866 is fired. The result is immediately shown on the
camera’s LCD monitor.
Flash power is automatically controlled by the camera and the most proper
exposure is obtained on your picture.
When you change the focal length of your camera lens, Di866 responds without
delay and set its light source for the proper illumination angle.
The battery compartment is specially
designed so that every cell is placed in the
same direction to avoid the confusion in
poor light condition.
designed so that every cell is placed in the
same direction to avoid the confusion in
poor light condition.
It is recommended to use all 4 batteries in same brand and type, and
replace them all at the same time.
Wrong insertion of each cell would not make electric contact.
replace them all at the same time.
Wrong insertion of each cell would not make electric contact.
+/- symbol is clearly marked at the battery
compartment.
compartment.
Place the battery magazine back into the
body.
body.
7
8
9
10
!
1.
2.
The power is automatically turned off (to stand-by mode), in about 30 sec.
of idle use on the camera or after the last setting job. To save the battery
energy, you can select the display-off setting from the custom setting. In
this case, the display screen turns off in about 8 sec. of idle use.
While Di866 is in the stand-by mode, display screen turns off and the pilot
lamp blinks every 2 seconds showing the flash unit is in stand-by mode.
To turn on Di866 again, press the camera’s shutter button halfway or
press any button of the flash unit.
of idle use on the camera or after the last setting job. To save the battery
energy, you can select the display-off setting from the custom setting. In
this case, the display screen turns off in about 8 sec. of idle use.
While Di866 is in the stand-by mode, display screen turns off and the pilot
lamp blinks every 2 seconds showing the flash unit is in stand-by mode.
To turn on Di866 again, press the camera’s shutter button halfway or
press any button of the flash unit.
In case Di866 is not in use over 30 minutes, the unit is completely turned
off and shut out the current leakage from the batteries.
To turn on Di866 again, take the first step of turning the flash unit on.
In case of using Di866 in off-camera-use mode (Wireless TTL flash-slave,
Universal Slave function), it is recommended to change the turn off timer
at the Custom setting....ref. page 32 .
The mode and the value set on the flash unit before turning off is
memorized and returns in the same condition when switch it on again.
off and shut out the current leakage from the batteries.
To turn on Di866 again, take the first step of turning the flash unit on.
In case of using Di866 in off-camera-use mode (Wireless TTL flash-slave,
Universal Slave function), it is recommended to change the turn off timer
at the Custom setting....ref. page 32 .
The mode and the value set on the flash unit before turning off is
memorized and returns in the same condition when switch it on again.
1.
2.
4.
When the recycle time becomes longer
than 20 sec., replace the batteries with the
fresh ones or recharge the batteries
(rechargeable batteries).
than 20 sec., replace the batteries with the
fresh ones or recharge the batteries
(rechargeable batteries).
3.
Turn off the power switch of both Di866
and the camera
and the camera
Turn the lock ring of Di866 to loosen it all
the way as shown in the picture.
the way as shown in the picture.
Slide the mounting foot of Di866 into the
hotshoe of the camera.
hotshoe of the camera.
Turn the lock ring to opposite direction
and tighten it.
and tighten it.
1.
2.
3.
4.
Lock pin comes out to hook the foot at the
hotshoe for sure contact.
hotshoe for sure contact.
5.
Loosen the lock ring and slide the mounting foot of Di866 off the hotshoe of
the camera. Make sure to turn the lock ring all the way to completely clear
the lock pin off the hooking slot on the hotshoe.
the camera. Make sure to turn the lock ring all the way to completely clear
the lock pin off the hooking slot on the hotshoe.
Inserting batteries
Turn on the flash unit
Mounting Di866 on the Camera
Removing Di866 from the Camera
Di866 has energy saving double power off function.
Full Automatic Flash Control
Usable batteries - Alkaline batteries, Lithium batteries, NiMH batteries.
The modes to be set on the camera:
In all those camera’s modes listed above, Di866 will automatically
and fully work in ETTL automatic flash control system.
and fully work in ETTL automatic flash control system.
(Full Auto), (Program), (Shutter priority),
Portrait, Landscape, Close-up, Sports,
Tv
Av
A-DEP
Night Portrait.
(Aperture priority), (Manual), Automatic depth-of-field,