American Standard Personal Lift 2403 사용자 설명서
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Regular Screwdriver
Adjustable Wrench
Sealant
Tape Measure
Hacksaw
Wax Ring/Gasket
Flexible Supply Tube
Closet Bolts
Carpenters Level
1
REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
SAVE FOR FUTURE USE
3
2
CLOSET FLANGE
CLOSET BOLTS
7 3 0 1 1 2 3 - 1 0 0 R e v . D
A
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 0 9
© A S A m e r i c a , I n c . 2 0 0 9
NOTE: Pictures may not exactly define contour of china and components.
COMPACT CADET® 3 - 1.6 GPF ONE-PIECE TOILET
COMPACT CADET® 3 FloWise™ - 1.28 GPF ONE-PIECE TOILET
COMPACT CADET® 3 FloWise™ - 1.28 GPF ONE-PIECE TOILET
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must be as listed below:
NOTE: Distance from wall to closet flange centerline must be as listed below:
5
4
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP" must face up!
a. Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP" must face up!
WAX RING
SEALANT
WASHER
NUT
FLANGE
BOLT
TH
IS SIDE UP
Model 2403 – Compact Elongated Right Height™ with Seat
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure
your installation conforms to local codes.
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure
your installation conforms to local codes.
!
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°, and slide
into place 6" (152 mm) apart and parallel to wall.
Install closet bolts in flange channel, turn 90°, and slide
into place 6" (152 mm) apart and parallel to wall.
724mm
(28-1/2)
159mm
(6-1/4)
16 ± 6mm
(5/8 ± 1/4)
(5/8 ± 1/4)
419mm
(16-1/2)
292mm
(11-1/2)
267mm
(10-1/2)
724mm
(28-1/2)
381mm
(15)
394mm
(15-1/2)
79mm
(3-1/8)
FINISHED WALL
422mm
(16-5/8)
305mm
(12)
C/L OF OUTLET
241mm
(9-1/2)
140mm
(5-1/2)
SUPPLY
AS
REQ'D
*
FINISHED
FLOOR
FLOOR
C/L OF SEAT POST
HOLES 140mm
(5-1/2) CENTERS
HOLES 140mm
(5-1/2) CENTERS
INSTALLATION INSTRUCTIONS