Bushnell 514 사용자 설명서
STANDARD EQUIPMENT
•
Complete Main Telescope Assembly
•
Altazimuth Yoke Mount
•
Variable Height-Hardwood Tripod
•
4mm, 12mm, 20mm focal length - Eyepieces.
•
5 x 24mm Finderscope w/ focus adjustment
•
Vertical Stabilizer Bar
•
Accessory Tray
•
Diagonal Mirror
•
3x Barlow, Erecting Lens
•
Hardware Pack
Tripod leg: 3-2_”bolts, 6-
11
/16
washers and 3-wingnuts
Accessory tray: 3-_” bolts, 6-_” washers and 3-wingnuts
Tripod Leg Lock Screws: 3 pc.
Stabilizer Bar: 1 Mounting Screw
Tripod Leg Lock Screws: 3 pc.
Stabilizer Bar: 1 Mounting Screw
TELESCOPE ASSEMBLY
1.
Remove all components from the carton and identify all components. READ THROUGH ASSEMBLY
INSTRUCTION BEFORE YOU ASSEMBLE YOUR TELESCOPE
2.
Set-Up Tripod, Mount and Accessory Tray
•
Select one
Tripod Leg (5)
and extend the
Tripod Leg Middle Section (6).
Using
Tripod Leg Lock Screws (9)
included in the hardware pack, insert the
Tripod Leg Lock Screw
into
the lower brackets on the
Tripod Leg.
Tighten the
Tripod Leg Lock
Screws
so that the middle section is securely in place. Repeat on
remaining two legs.
•
Locate the
Altazimuth Yoke Mount (3).
Note: Before assembling tripod
legs to Altazimuth Yoke Mount, make sure the Accessory Tray Braces(7)
face inward.
face inward.
Locate the long bolts and washers from the hardware
pack (
3-2_”bolts, 6-
11
/16
washers and 3-wingnuts)
. Position the mount over the
Tripod Leg (5)
as shown
(fig. 1).
and align the holes in the
Tripod Leg
with the holes in the mount. Insert the bolts through the holes at the
top of a
Tripod Leg.
A washer should be positioned on both outer
sides of the
Tripod Leg.
Attach a wing nut to the bolt but do not
tighten it all the way. Repeat on the remaining two
Tripod Legs
. Once
you have attached all
Tripod Legs
to the mount, securely tighten all
wing nuts.
•
Locate the
Accessory Tray (8).
Using the accessory tray bolts, wingnuts and washers
( 3-_” bolts, 6-_
washers and 3 - wingnuts)
connect the
Accessory Tray
to the
Accessory Tray Braces (7).
Start with one
Tripod
Leg
and attach wingnut. Wingnuts should be positioned beneath the
Accessory Tray.
Do not tighten
wingnuts until all
Accessory Tray Braces
are attached as some adjustments may be required.
3.
Attach Telescope and Finderscope
•
Locate
Telescope Main Tube (20).
Now, locate the
Vertical Stabilizer Bar (10)
and insert the
Vertical
Stabilizer Bar
into the slot at the base of the
Altazimuth Yoke Mount (3)
. Then, secure telescope to
Altazimuth Yoke Mount
by removing
Altitude Lock Knobs (19).
from telescope and positioning the
telescope between yoke. Carefully replace the
Altitude Lock Knobs
and remove lens cover from
60mm
Objective Lens (1).
Locate the
Stabilizer Bar Mounting Screw (2)
in the hardware pack. Insert the
Stabilizer Bar Mounting Screw
into the slot to secure the
Vertical Stabilizer Bar
in place.
•
Locate the
Finderscope (17)
with pre-assembled
Finderscope Mount (15).
Remove the two nuts located
near the back of the
Telescope Main Tube (20)
and place the
Finderscope
and
Mount
assembly over the
exposed screws. Replace the nuts, and securely tighten the
Finderscope Mount
in place.
fig. 1