Bil-Jax Personal Lift ESP 19 사용자 설명서
2-1
2
Introduction
2-1
or to ride on the plat-
at
upper mast sections are
-
vel is enabled with the joystick. In case of a loss of battery power, a manual free
unctions except platform lowering if the lift vehicle base is more than one degree
off, turning an emergency lowering valve knob lowers the
et per second, whether the
Carefully read and understand all of the safety instructions in Section 1 and all operating
instructions in Section 3 of this manual before operating the lift vehicle.
instructions in Section 3 of this manual before operating the lift vehicle.
GENERAL DESCRIPTION
The ESP 19 hydraulic lift is designed and manufactured for use as a warehouse stocking
and order picking vehicle. Its guard rail design permits the operat
form with the load, while transferring parts to and from multiple overhead storage loca-
tions. The maximum platform load is limited to 450 lbs.
and order picking vehicle. Its guard rail design permits the operat
form with the load, while transferring parts to and from multiple overhead storage loca-
tions. The maximum platform load is limited to 450 lbs.
All ESP 19 operations are powered by a 24-Volt DC battery package. A 40-amp battery
charger and plug-in receptacle are included in the system for recharging the batteries
the end of each work period. A charge level indicator displays the battery charge status.
charger and plug-in receptacle are included in the system for recharging the batteries
the end of each work period. A charge level indicator displays the battery charge status.
The platform lift function is hydraulic, including a hydraulic cylinder, reservoir, and
pump. The hydraulic pump motor is driven by a 24-Volt DC electric motor. Elevation is
by a 1-3/4 inch linear-displacement hydraulic cylinder and four telescoping mast sec-
tions. The lower mast section is raised by hydraulic cylinder. The
raised mechanically by connecting sets of chains and sheaves (pulleys). The lift platform
rises four inches for each inch of hydraulic cylinder extension.
pump. The hydraulic pump motor is driven by a 24-Volt DC electric motor. Elevation is
by a 1-3/4 inch linear-displacement hydraulic cylinder and four telescoping mast sec-
tions. The lower mast section is raised by hydraulic cylinder. The
raised mechanically by connecting sets of chains and sheaves (pulleys). The lift platform
rises four inches for each inch of hydraulic cylinder extension.
Other electrically powered functions include a two-wheel drive transaxle for floor travel
and pushbutton steering. The maximum travel speed is enabled only when the lift plat-
form is down. When the platform is raised, the travel speed is limited. The transaxle in-
cludes an electric brake that locks the drive wheels whenever forward or reverse travel is
halted. The electric brake is normally applied; the brake disengages when forward or re
verse tra
wheel lever can be used to disengage the electric brake, allowing the lift vehicle to be
towed.
and pushbutton steering. The maximum travel speed is enabled only when the lift plat-
form is down. When the platform is raised, the travel speed is limited. The transaxle in-
cludes an electric brake that locks the drive wheels whenever forward or reverse travel is
halted. The electric brake is normally applied; the brake disengages when forward or re
verse tra
wheel lever can be used to disengage the electric brake, allowing the lift vehicle to be
towed.
Floor travel and platform lift functions are controlled from an upper control box located
on the lift platform. Floor travel is by joystick control with pushbutton steering. Lift
functions are by pushbutton control. Platform lift can also be controlled from a lower
control box mounted on the vehicle base. An electronic level sensor disables all lift and
travel f
out of level. While out of level, travel can be resumed after the lift platform is fully low-
ered.
on the lift platform. Floor travel is by joystick control with pushbutton steering. Lift
functions are by pushbutton control. Platform lift can also be controlled from a lower
control box mounted on the vehicle base. An electronic level sensor disables all lift and
travel f
out of level. While out of level, travel can be resumed after the lift platform is fully low-
ered.
With equipment power on or
lift platform at a controlled, safe speed. The lowering valve knob is visible and readily
accessible from floor level.
lift platform at a controlled, safe speed. The lowering valve knob is visible and readily
accessible from floor level.
Proper lift vehicle operation and safety are assured by performing the scheduled inspec-
tion and maintenance procedures set forth in this manual. The risk of platform free-fall is
eliminated by proper maintenance of the chains, sheaves and sheave pins, a properly in-
stalled flow restrictor valve, and a clean mast. The restrictor valve (non-adjustable) fixes
the maximum rate of platform descent to approximately 0.6 fe
platform is empty or fully loaded. With the restrictor valve properly installed, a hydraulic
hose failure will result in the same maximum rate of descent.
tion and maintenance procedures set forth in this manual. The risk of platform free-fall is
eliminated by proper maintenance of the chains, sheaves and sheave pins, a properly in-
stalled flow restrictor valve, and a clean mast. The restrictor valve (non-adjustable) fixes
the maximum rate of platform descent to approximately 0.6 fe
platform is empty or fully loaded. With the restrictor valve properly installed, a hydraulic
hose failure will result in the same maximum rate of descent.