Boss Audio Systems GT-100 사용자 설명서

0–100

This adjusts the input sensitivity when INPUT 
LEVEL is selected for SOURCE .

*  If you want to light the ACCEL/CTL pedal’s LED indicator while the 

ASSIGN 1–8 function is assigned to the ACCEL/CTL pedal, set the ACCEL/

CTL pedal FUNC (p . 31) to “LED ON/OFF .”

OFF, ON

Turns the ASSIGN 1–8 on/off .

EXP PEDAL

Assigns the GT-100’s [EXP] pedal .

EXP PDL SW

Assigns the EXP pedal switch .

P .LOOP PEDAL

Assigns the GT-100’s [PHRASE LOOP] pedal .

ACC/CTL PDL

Assigns the [ACCEL/CTL] pedal .

SUB EXP PDL

Assigns the external expression pedal (such as 

the separately available EV-5) connected to the 

SUB CTL 1, 2/SUB EXP jack .

SUB CTL1 PDL

Assigns the external footswitch (FS-5U, FS-6; 

available separately) connected to the SUB CTL 

1, 2/SUB EXP jack .

SUB CTL2 PDL

Assigns the external foot switch (FS-5U, FS-6; 

available separately) connected to the SUB CTL 

1, 2/SUB EXP jack .

INT PEDAL

Refer to “Virtual expression pedal system 

WAVE PEDAL

Refer to “Virtual expression pedal system 

INPUT LEVEL

The assigned target parameter will change 

according to the input level .

CC#1–#31

Control Change messages from an external MIDI 

device .

CC#64–#95

Control Change messages from an external MIDI 

device .

MOMENT

The normal state is Off (minimum value), with 

the switch On (maximum value) only while the 

footswitch is depressed .

TOGGLE

The setting is toggled On (maximum value) 

or Off (minimum value) with each press of the 

footswitch .

This selects the parameter to be changed .
Refer to TARGET list

This sets the minimum value for the range in which the parameter 

can change . The value differs depending on the parameter 

assigned for TARGET parameter .

This sets the maximum value for the range in which the parameter 

can change . The value differs depending on the parameter 

assigned for TARGET parameter .

ACT RANGE LO 0–126

You can set the controllable range for target 

parameters within the source’s operational 

range . Target parameters are controlled within 

the range set with ACT RANGE LO and ACT 

RANGE HI . You should normally set ACT RANGE 

LO to 0 and ACT RANGE HI to 127 .

ACT RANGE HI 1–127

0–100,  
BPM  –

This determines the time spend for one cycle of 

the assumed EXP Pedal .

When set to BPM, the value of each parameter will be set accord-

ing to the value of the “MASTER BPM” specified for each patch . This 

makes it easier to achieve effect sound settings that match the 

tempo of the song .
*  If, due to the tempo, the time is longer than the range of 

allowable settings, it is then synchronized to a period either 1/2 

or 1/4 of that time .

SAW

TRI

SINE

PATCH CHANGE This is activated when a patch is selected .

EXP PDL-LO

This is activated when the GT-100’s [EXP] pedal is 

set to the minimum position .

EXP PDL-MID

This is activated when the GT-100’s [EXP] pedal is 

moved through the middle position .

EXP PDL-HI

This is activated when the GT-100’s [EXP] pedal is 

set to the maximum position .

EXP PDL SW

This is activated when the EXP pedal switch is 

operated .

P .LOOP PEDAL

This is activated when the [PHRASE LOOP] pedal 

is operated .

ACC/CTL PDL

This is activated when the [ACCEL/CTL] Pedal is 

operated .

SUB EXP PDL

This is activated when an external expression 

pedal connected to the SUB CTL 1, 2/SUB EXP 

jack is operated .

SUB CTL1 PDL

This is activated when an external footswitch 

connected to the SUB CTL 1, 2/SUB EXP jack is 

operated .

SUB CTL2 PDL

This is activated when an external footswitch 

connected to the SUB CTL 1, 2/SUB EXP jack is 

operated .

CC#1–#31

This is activated when a control change is 

received .

CC#64–#95

This is activated when a control change is 

received .

0–100

This specifies the time over which the internal 

pedal will move from the toe-raised position to 

the toe-down position .

LINEAR

SLOW RISE

FAST RISE

*1 The WAVE RATE and WAVEFORM parameters are enabled when the Source 

parameter is set to WAVE PEDAL .

*2 The INT PDL TRIGGER, INT PDL TIME, and INT PDL CURVE parameters are enabled 

when the SOURCE parameter is set to INT PEDAL .