Troy-Bilt 24B-060F766 사용자 설명서
9
•
Twist the two buttons on the back of the bag to
unlock and empty contents. See Figure 7.
unlock and empty contents. See Figure 7.
•
Hold bag handle and bag clip while emptying the
contents.
contents.
•
Compress bag opening and fold inner flap over
opening.
opening.
•
Fold outer flap over inner flap and insert buttons on
the bag through metal outlets.
the bag through metal outlets.
•
Twist the buttons to lock bag.
Figure 7
To Remove Blower Chute
(If Equipped)
•
Grasp blower chute with one hand and pull lock rod
on mounting bracket with other hand toward engine
to release. Refer to Figure 5.
on mounting bracket with other hand toward engine
to release. Refer to Figure 5.
•
Remove blower chute from rim of the discharge
opening.
opening.
Using the Nozzle Vacuum
•
Place nozzle/hose vac handle in the top position on
the nozzle to vacuum through nozzle. See Figure 8.
the nozzle to vacuum through nozzle. See Figure 8.
•
The spring loaded pin must be in the first hole of the
hose adapter to operate the nozzle vac.
hose adapter to operate the nozzle vac.
•
Place both hands on top of upper handle to push
unit over yard waste.
unit over yard waste.
Yard waste such as leaves and pine needles can be
vacuumed up through the nozzle for shredding. After
material has been shredded by the flail blades on the
impeller assembly, it will be discharged into catcher bag
or through blower chute (if equipped). Do not attempt to
shred or chip any material other than vegetation found
in a normal yard (i.e. branches, leaves, twigs, etc.)
Avoid fibrous plants such as tomato vines until they are
thoroughly dried out. Materials such as stalks or heavy
branches up to 1 1/2” in diameter may be fed into the
chipper chute.
vacuumed up through the nozzle for shredding. After
material has been shredded by the flail blades on the
impeller assembly, it will be discharged into catcher bag
or through blower chute (if equipped). Do not attempt to
shred or chip any material other than vegetation found
in a normal yard (i.e. branches, leaves, twigs, etc.)
Avoid fibrous plants such as tomato vines until they are
thoroughly dried out. Materials such as stalks or heavy
branches up to 1 1/2” in diameter may be fed into the
chipper chute.
Figure 8
IMPORTANT:
The flail screen is located inside the
housing in the discharge area. If the flail screen
becomes clogged, remove and clean as instructed in
SECTION 5: MAINTAINING YOUR YARD VACUUM.
For best performance, it is also important to keep the
chipper blade sharp.
becomes clogged, remove and clean as instructed in
SECTION 5: MAINTAINING YOUR YARD VACUUM.
For best performance, it is also important to keep the
chipper blade sharp.
WARNING: Do not at any time make any
adjustments without first stopping engine
and disconnecting spark plug wire.
adjustments without first stopping engine
and disconnecting spark plug wire.
Using the Hose Assembly
•
Place nozzle/hose vac handle in the bottom
position on the nozzle to redirect vacuum to the
hose assembly. See Figure 9.
position on the nozzle to redirect vacuum to the
hose assembly. See Figure 9.
•
The spring loaded pin must be in the second hole of
the hose adapter to operate the hose assembly.
the hose adapter to operate the hose assembly.
•
Unhook the hose from upper handle bracket and
grasp the hose handle to guide while vacuuming
yard waste such as leaves or pine needles in hard
to reach places.
grasp the hose handle to guide while vacuuming
yard waste such as leaves or pine needles in hard
to reach places.
Figure 9
Buttons
Inner Flap
Outer Flap
Bag Handle
Strap
Bag Clip
Nozzle/Hose
Vac Handle
Vac Handle
Spring Loaded Pin
(First Hole)
(First Hole)
(Top Position)
Nozzle/Hose
Vac Handle
Vac Handle
Spring Loaded Pin
(Second Hole)
(Second Hole)
(Bottom Position)