Philips DVDR3390 전단

1

Connect

2

Set up

Start with the ‘Basic Connection.’
If you have a Cable Box or Satellite Receiver, follow the instructions for ‘Connection with a Cable Box or 
Satellite Receiver’. 

~

R

Television (rear)

Philips 
recorder 
(rear)

~

R

Television (rear)

Philips recorder 
(rear)

Philips recorder (front panel)

To AC
power

Basic Connection

A

 

Before connecting, unplug the antenna cable that 
is currently connected to your TV.

B

 

Connect the antenna cable to the ANTENNA-
IN 

jack on the recorder.

C

 

Use the supplied RF coaxial cable to connect the 
TV-OUT 

 jack on this recorder to the 

Antenna In jack on the TV.

D

 

Use the supplied audio/video cable (yellow plug) 
to connect the VIDEO (CVBS) -OUT1 jack on 
this  recorder to the VIDEO IN jack on the TV.

E

 

Use the supplied audio/video cable (red/ white 
plugs) to connect the AUDIO OUTPUT jacks 
on this recorder to the AUDIO IN jacks on the 
TV.

F

 

Connect the power cable from the recorder to 
an AC power outlet.

Connection with a Cable Box 
or Satellite Receiver

To antenna or 
set-top box

To AC
power

A

 

Keep the existing antenna connection from the 
Antenna TV signal to the Cable Box/ Satellite 
Receiver.

B

 

Use an antenna cable to connect the ANTENNA-
IN 

jack on the recorder to the RF OUT jack on 

the Cable Box/Satellite Receiver.

C

 

Follow steps 

C

 to 

E

 under ‘Basic Connections’ 

before you proceed to step 

D

 below. 

   

Note The antenna connection may be different 

 

depending on the Satellite Receiver/Cable Box. 

 

Refer to its user manual for proper antenna 

 connection.

D

 

Use a yellow video cable (not supplied) to connect  
the VIDEO (CVBS) EXT 1 jack on this 
recorder to the VIDEO OUT jack on the Cable 
Box/ Satellite Receiver.

E

 

Use another red and white audio cable (not    
supplied) to connect the AUDIO INPUT jacks  
on this recorder to the AUDIO OUT jacks on the 
Cable Box/ Satellite Receiver.

A

 

Select the video input channel on  

 your TV

A

 

Press STANDBY-ON on the recorder.

B

 

Turn on the TV.

   

Note If connected to your VCR, make sure it is 

 

switched off or in standby mode before proceeding.

C

 Press 

SYSTEM MENU 

.

D

  Select the TV’s video input channel that corresponds 

to the jacks connecting the recorder to the TV. 

   

Note Video Input selection varies for different 

 

brands/models of TVs. Consult the user manual that 

 

came with your TV if none of the below is successful.

 

Press channel 2 on your TV. Then press the channel 
down button to locate the video input channel. (This 
channel is usually located between the lowest and 
highest TV channels.) 

 

OR, for some TVs, there may be a button on the 
TV’s remote control that accesses the video input 
channel labeled SOURCE, AV or SELECT.

 

OR, select the Video Input Channel from the TV’s 
on-screen menu system.

 

Note Consult your TV manufacturer if none of the 

 

above is successful.

B

 

Initial Installation

A

 Press SYSTEM MENU 

 on the remote    

control.

 

Note Use up 

 / down 

 keys to toggle 

 

through the options. Select an item by pressing

  

right 

.  To confi rm a setting, press OK 

.

B

  

Setup and install TV channels.

 

 

Highlight 

 and press right 

. 

 Select { Tuner Input Source } and press  
OK 

.

 

 

 

 

{ Cable } 

 

if the recorder is connected directly to the cable 

 

signal or through set-top box.

  

{ Air } 

 

if the recorder is connected directly to an indoor 

 

or outdoor antenna.

     

Note Press OK 

 to confi rm your selection.

 

Select { Channel Search } and press OK 

  

on the remote control to start automatic TV    
channel search.

   

Note If using a cable box/ satellite receiver,  you 

 

may only pick up one channel. Leave the recorder on 

 

this channel and change channels at the cable box or 

 satellite 

receiver. 

C

  

Select the language.

 

 

Highlight 

 and press right 

.  

 

– selects TV On-Screen Display language.

 

– selects default Disc Menu language.

 

– selects default subtitle language.

 

– selects default audio language.

D

  

Select the date and time.

 

 

Highlight 

 and press right 

.  

  

Use 

the numeric keypad 0 

 to    

  input the date/time, then press OK

 

 

to  

 

 confi rm.

E

   Press  SYSTEM MENU 

 to exit.

To antenna 
or set-top 
box

Cable Box/Satellite Receiver (rear)

dvdr3390_37_eng_qsg_20932b.indd   2

dvdr3390_37_eng_qsg_20932b.indd   2

2006-12-08   1:24:55 PM

2006-12-08   1:24:55 PM