Marshall electronic V-R70DP 사용자 설명서
V-R70DP
Users Guide
4
5
Electrical Specifi cations
Display (Viewing Area)
7” (6.14”H × 3.27”V) (156.0mm x 83.28mm)
Viewing Angles
150° x 130°
Resolution (RGB Dots)
800H×RGBx480V (1.2 million pixels)
Contrast Ratio
300:1
Dot Pitch
0.1905 Square Pixel
Pixel Response
12ms rise / 18ms fall
Backlight Type / Life
CCFL / 10,000 to 20,000 Hours Typical
Brightness
400 cd/m²
LCD Screen Treatments
Anti Reflection, Anti Glare, Hardcoat
Protective Screen
0.118” (3mm) thick Optical Grade Polycarbonate with Anti-Glare and Anti-Abrasion
coatings. (600 Cheesecloth mil-M-13508C)
coatings. (600 Cheesecloth mil-M-13508C)
System
NTSC/PAL auto recognition
Inputs
2 Analog Composite (BNC)
S-Video (Y/C) (4 pin mini din female)
3 Lamp Tally (DB-15 Female)
Power (4 pin male XLR)
S-Video (Y/C) (4 pin mini din female)
3 Lamp Tally (DB-15 Female)
Power (4 pin male XLR)
Active Outputs
2 Composite Video (BNC) Available when power is applied to monitor
Color temperature
D65 (6500° Kelvin)
Color Gamut
SMPTE-C of CEI-1931 65%
Luma Linearity
Typical +/- 3% with 5 ire increments (0 to 10 ire)
6
Mechanical Specifi cation
Dimensions
7.44”W x 5.125”H x 2.5”D (18.89cm x 13.0cm x 6.35cm)
Approx. Weight
3 lbs
Power Consumption
14-10 VDC, 15 Watt nominal
(3.0Amps max - UL Class 2 supply included)
(3.0Amps max - UL Class 2 supply included)
Operating Temperature
-20” C to 65” C Ambient
Storage Temperature
-30” C to 85” C
7
Faceplate Cleaning
Faceplate Cleaning
When cleaning the faceplate it is very important to use non-abrasive and ammonia free cleaning agents and a clean micro fi ber
cloth. Do not use paper towels. Paper towel fi bers are coarse and may scratch the surface of the Polycarbonate faceplate.
Paper towels may also leave streaks on the surface. Antistatic and fi ngerprint resistant cleaning agents are recommended.
Wash protective cover with a solution of mild soap or detergent and lukewarm water. Use a clean soft cloth, applying only light pres-
sure. Rinse with clean water and dry by blotting with a damp cloth or chamois. Grease, oil or tar may be removed with a good grade
of hexane, aliphatic naphtha, or kerosene. These solvents may be obtained at a paint or hardware store and should be used in ac-
cordance with manufacturer’s recommendations.
When cleaning the faceplate it is very important to use non-abrasive and ammonia free cleaning agents and a clean micro fi ber
cloth. Do not use paper towels. Paper towel fi bers are coarse and may scratch the surface of the Polycarbonate faceplate.
Paper towels may also leave streaks on the surface. Antistatic and fi ngerprint resistant cleaning agents are recommended.
Wash protective cover with a solution of mild soap or detergent and lukewarm water. Use a clean soft cloth, applying only light pres-
sure. Rinse with clean water and dry by blotting with a damp cloth or chamois. Grease, oil or tar may be removed with a good grade
of hexane, aliphatic naphtha, or kerosene. These solvents may be obtained at a paint or hardware store and should be used in ac-
cordance with manufacturer’s recommendations.
DO NOT USE: window cleaning sprays, kitchen scouring compounds or solvents such as acetone, gasoline, benzene,
alcohol, carbon tetrachloride, or lacquer thinner. These can scratch the sheet’s surface and/or weaken the sheet causing
small surface cracks called “crazing.”
alcohol, carbon tetrachloride, or lacquer thinner. These can scratch the sheet’s surface and/or weaken the sheet causing
small surface cracks called “crazing.”
Faceplate Dusting
Dust with a soft, damp cloth or chamois. Dry or gritty cloths may cause surface scratches and create a static electric charge on the
surface. Neutralizing static electricity effects by using recommended cleaning and polishing practice.
Dust with a soft, damp cloth or chamois. Dry or gritty cloths may cause surface scratches and create a static electric charge on the
surface. Neutralizing static electricity effects by using recommended cleaning and polishing practice.
Faceplate Polishing
Protect and maintain surface gloss by occasional polishing with a good plastic cleaner and polish. Apply a thin, even coat with a soft
clean cloth and polish lightly with cotton fl annel. Then wipe with a damp cloth to help eliminate electrostatic charges that can attract
dust particles
Protect and maintain surface gloss by occasional polishing with a good plastic cleaner and polish. Apply a thin, even coat with a soft
clean cloth and polish lightly with cotton fl annel. Then wipe with a damp cloth to help eliminate electrostatic charges that can attract
dust particles
Marking on the Faceplate
Use SHARPEE or equivalent marker. Clean as per instructions with an ammonia free cleaning agent.
Use SHARPEE or equivalent marker. Clean as per instructions with an ammonia free cleaning agent.