Contemporary Research ICC/ICW-HE 전단

Size: 

19" [483mm] wide x 1.75" [38mm] height (1RU) x 9" [229mm] deep

Weight: 

3 lbs [1.36kg]

Enclosure:

All aluminum with durable black powder coat paint

Mounting:

Shelf or 19" equipment rack (mounting brackets included)

RF Out Adjust:

Trims iCC-Net channel output, shipped set to +55 dBmV

RS-232 TX LED:

Yellow LED, lights when receiving RS-232 data on Control or iC-Net RS-232 port

RS-232 TX LED:

Yellow LED, lights when receiving RS-232 data on Control or iC-Net RS-232 port

RS-232 DIP Switch: Sets RS-232 baud rate (9600 - 38.4K), 8 data bits, no parity, 1 stop bit 

Selects high/low sensitivity for RF In signal

Net LED:

Green LED for iC-Net bus, flashes once per second if network is operating, device numbers agree

LED will flash twice per second if the number of present and expected devices do not match

COM LED: 

Yellow LED blinks when a valid command is received or system response sent through the Control port

Error LED: 

Red LED indicates a problem within the unit

Reset/Default:

White button sends press and release response to PC software or control system

Emergency:

Red button sends press and release response to PC software or control system

Control RS-232:

DB9 female, RS-232 data link to control system or PC

iC-Net RS-232:

DB9 female, RS-232 data link to send iCW-Net over fiber or codec

I/O 1 & 2:

4-pin captive screw terminal for Input/Outputs 1 and 2

2 switch closures or inputs, max 50 mA, 24 VDC, switch to GND

I/O Applications: DC power - close pins 1 & 3 to provide DC on/off

Dry closure 2 - close pins 3 & 4 for dry contact to external power relay, AMX PC1 or similar

Sense closure (3 & 4) on Input 1 - trigger control system to power off for all rooms

iCW-Net 2, 3:

RJ-45 female 8 pin Telco jack, supports 3300 ft [1 km] of wire

RS-422 type data requiring at least 2 twisted wire pairs with shield or fifth conductor

iCW-Net 1:

6-pin captive-screw terminal for system wiring or use with RS-422-format fiber or codecs

iC-Net Expand:

RJ-11 female 6-pin Telco jack

CAT3/CAT5 compatible unshielded, max 3,300 feet [1 Km] from Head End

Power In:

2.1mm coaxial jack (inside center conductor positive), 300 mA maximum

11 to 18 VDC, 12 VDC typical (may be unregulated)

RF In:

'F', female, 75 ohm impedance, RF and iCC-Net from CATV system

Data Receive:

Carried over the same RF coax connection as TV channels

Return signal from system controllers

Sub-band, 5.6MHz, narrow-band signal below standard sub-band channels

-15 to +35 dBmV signal level (0 to +15 dBmV nominal)

RF Out:

‘F', female, 75 ohm impedance, RF to CATV distribution to TVs, tuners, and controllers

Data Transmit:

Mid-band VHF, 74.7 MHz, narrow-band signal between channels 4 and 5

± 80 KHz max carrier deviation

+55 dBmV maximum (default)

19" Mounting hardware

10 dB RF attenuator (ICC-HE only)

12 VDC Power Supply (North American shipments only)

Contemporary Research z 17630 Davenport z Suite 113, Dallas, Texas z 75252-5963

Phone: (972) 931-2728 z Toll Free: (888) 972-2728 z Fax: (972) 931-2765