Petmate Le Bistro 사용자 설명서

READ ALL INSTRUCTIONS BEFORE OPERATING THE PRODUCT.
A. To Install Batteries:
1) Turn the base upside down and remove battery cover.
2)  Install 3 new “D” cell, alkaline batteries. 

(Be sure to match positive and negative markings).

3) Replace battery cover. Be sure to “snap” in place.

To Turn Unit ON:
1)  Press the (-) side of the On/Off switch DOWN. (located on the bottom of the base)
2)  Set unit right side up. (LCD screen should be facing you 

NOTE: Clock will flash “12:00 A.M.” automatically.

3)  Press ENTER button to set current time. First the HOUR will be flashing.
4)  Use UP or DOWN arrow buttons to set current HOUR. (until it is correct) 

NOTE: the clock will automatically change to A.M. or P.M. as you scroll through the hours.

5)  Press ENTER button again and the MINUTES will start flashing.
6)  Use UP or DOWN arrow buttons to set current MINUTES.
7)  Press ENTER upon completion. 

NOTE: Clock will be set after setting minutes and the unit is now in AUTOMATIC MODE.

While setting current time, if the programming is not completed the Portion Control LeBistro

®

 waits until the current time is 

set and will not go into AUTOMATIC MODE.

SETTING ANY MEAL, MEAL TIME and MEAL SIZE:
B. To Set Meal Selection:
1)  Press and Hold the ENTER button for 2 seconds. “MEALS” will flash.
2)  Use UP or DOWN arrow buttons to select the desired Meal to be programmed. (Breakfast, Lunch or Dinner will flash as 

UP and DOWN arrows buttons are pressed)

3) Press the ENTER button after you select the Meal.
a)  “Yes” will Flash. Press the ENTER if you want to set the meal time.
b)  If you do not wish to set that meal time, press the DOWN arrow to select “No” and press ENTER. 

Note: (if “No” is selected, press ENTER and the software takes you back to “MEALS”. Use UP or DOWN arrows buttons 
to select the desired Meal to be programmed)

To Set Meal Time:
After selecting the MEAL to be programmed and selecting “Yes”, the HOUR will flash.
1)  Use UP or DOWN arrow buttons to set Meal HOUR. (until it is correct) 

NOTE: that clock will automatically change to A.M. or P.M. as you scroll through the Hours.

2)  Press ENTER button again and the MINUTES will start flashing.
3) Use UP or DOWN arrow buttons to set Meal MINUTES.
4)  Press Enter button when minutes are set. 

To Set Meal Size:
After setting Meal Time, the “Meal Size” Menu will flash. (right side of display)
1)  Use UP or DOWN arrow buttons to increase or decrease amount of food to be dispensed. For example; to feed 1 cup 

meal size, press the UP arrow button until 4 bars are displayed.

2)  Press Enter upon completion. NOTE: Each bar equals approximately 1/4 cup. Themaximummeal size youmay select 

is 3 cups.

C. To Set Other Meals:
After any Meal has been programmed (inclusive of time and size) “MEALS” will flash and Meals programmed will show 
on screen.
1) Clock will display current time.
2)  REPEAT “Meal Selection” programming directions. NOTE: if you only wish to set 1 Meal, press ENTER while “MEALS” is 

flashing and unit will go into AUTOMATIC MODE.

PROGRAMMING COMPLETE
After all meals are set:
1)  Press ENTER 

NOTE: After programming of all meals in completed, press ENTER while “MEALS” is flashing and unit will go into 
Automatic Mode.

D.  Meals Served 

“SERVED” will show on screen at all times. This indicates number of Meals served. 1 digit equals 1 meal. Meals served 
will go up to 99 and then reset at 00. To reset the “SERVED” counter; press UP and DOWN Arrow buttons simultaneously 
and it will reset to 00. Meal Served counts up to 99, then resets

E.  Manual Feed Option 

Press and hold UP Arrow button for 3 seconds. 
NOTE: Food will be dispensed according to first Meal set (i.e. breakfast is set at 1/2 cup, then food will be dispensed in 
1/2 cup increments) Repeat if additional food is desired.

On/Off 
Switch

Time must be set before 
setup can continue

Press Up or Down Arrows to 
Program Meal Size

Hold for Manual Feed Option

Meal Served counts up 
to 99, then resets

Battery 
Casing