Pioneer DVR-S201 사용자 설명서
9
<DRC1101>
En
English
CONNECTION
7 Setting the SCSI ID
The SCSI ID is set using the switch on the device’s rear
panel.
The computer will recognize each connected SCSI device
by its SCSI ID.
Generally, the SCSI IDs are set as follows: “0” for a hard
disk, “3” for a CD-ROM and “7” for a SCSI interface board
(card). Refer to the operating instructions that accompany
each device to verify that all SCSI devices have different
IDs.
panel.
The computer will recognize each connected SCSI device
by its SCSI ID.
Generally, the SCSI IDs are set as follows: “0” for a hard
disk, “3” for a CD-ROM and “7” for a SCSI interface board
(card). Refer to the operating instructions that accompany
each device to verify that all SCSI devices have different
IDs.
1
GND
2
GND
3
GND
4
GND
5
GND
6
GND
7
GND
8
GND
9
GND
10
GND
11
GND
12
OPEN
13
OPEN
14
OPEN
15
GND
16
GND
17
GND
No.25
No.1
No.50
No.26
Pin No.
Signal
Pin No.
Signal
Pin No.
Signal
18
GND
19
GND
20
GND
21
GND
22
GND
23
GND
24
GND
25
GND
26
-DB0
27
-DB1
28
-DB2
29
-DB3
30
-DB4
31
-DB5
32
-DB6
33
-DB7
34
-DBP
35
GND
36
GND
37
OPEN
38
TERM PWR
39
OPEN
40
GND
41
-ATN
42
GND
43
-BSY
44
-ACK
45
-RST
46
-MSG
47
-SEL
48
-C/D
49
-REQ
50
-I/O
NOTES:
÷ Pin No. 12 to 14, 37 and 39 are not connected
÷ Low active signals are preceded by a “-”
÷ Shield-type connectors are required
÷ Pin No. 12 to 14, 37 and 39 are not connected
÷ Low active signals are preceded by a “-”
÷ Shield-type connectors are required
SCSI
ID
0
Press “+” to increase the number (0, 1, 2,...7) and “–” to
decrease the ID setting (7, 6, 5,...0).
decrease the ID setting (7, 6, 5,...0).
NOTES:
÷ The SCSI ID is preset to “0” at the factory.
÷ To prevent the switch from breaking, do not press “+”
÷ The SCSI ID is preset to “0” at the factory.
÷ To prevent the switch from breaking, do not press “+”
when the SCSI ID selection is set to “7” or “–” when
it is set to “0”.
it is set to “0”.
÷ This device will recognize setting the SCSI ID when the
power is turned on.
7 SCSI Connector Pin Configuration and Signals
Connector pin numbers and configurations are shown in
the following diagram.
the following diagram.
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the plug
by tugging the cord and never touch the power cord when
your hands are wet as this could cause a short circuit or
electric shock. Do not place the unit, a piece of furniture, etc.,
on the power cord, or pinch the cord. Never make a knot in the
cord or tie it with other cords. The power cords should be
routed such that they are not likely to be stepped on. A
damaged power cord can cause a fire or give you an electrical
shock. Check the power cord once in a while. When you find
it damaged, ask your nearest PIONEER authorized service
center or your dealer for a replacement.
by tugging the cord and never touch the power cord when
your hands are wet as this could cause a short circuit or
electric shock. Do not place the unit, a piece of furniture, etc.,
on the power cord, or pinch the cord. Never make a knot in the
cord or tie it with other cords. The power cords should be
routed such that they are not likely to be stepped on. A
damaged power cord can cause a fire or give you an electrical
shock. Check the power cord once in a while. When you find
it damaged, ask your nearest PIONEER authorized service
center or your dealer for a replacement.