Maytag MSB26C6MDH 사용자 매뉴얼

5. Slide the cap closed, and check that the indicator is visible 

through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator’s rear 
bubble has not been popped.

The disposable pouches should be replaced every 6 months, 
when the status indicator has completely changed from white to 
red. 

To order replacements, see “Accessories” in the User 
Instructions or User Guide. 

1. Remove the old pouches from the Produce Preserver 

housing.

2. Remove the old status indicator.

3. Install the new pouches and status indicator using the 

instructions in the previous sections.

The refrigerator and freezer controls are located on the dispenser 
panel.

IMPORTANT: The display screen on the dispenser control panel 
will turn off automatically and enter “sleep” mode when the 
control buttons and dispenser pad have not been used for 
2 minutes or more. While in “sleep” mode, the first press of a 
control button will only reactivate the display screen, without 
changing any settings. 

■

Touch any control button on the dispenser panel to activate 
the display screen. The home screen will appear as shown.  

For your convenience, your refrigerator and freezer controls are 
preset at the factory. When you first install your refrigerator, make 
sure that the controls are still set to the “mid-settings.” The 
factory recommended set points are 37°F (3°C) for the 
refrigerator and 0°F (-18°C) for the freezer. 

■

Wait 24 hours before you put food into the refrigerator. If you 
add food before the refrigerator has cooled completely, your 
food may spoil.

NOTE: Adjusting the set points to a colder than 
recommended setting will not cool the compartments any 
faster.

■

If the temperature is too warm or too cold in the refrigerator or 
freezer, first check the air vents to be sure they are not 
blocked before adjusting the controls.

■

The preset settings should be correct for normal household 
usage. The controls are set correctly when milk or juice is as 
cold as you like and when ice cream is firm.

■

Wait at least 24 hours between adjustments. Recheck the 
temperatures before other adjustments are made.

To view and adjust the set points, press and hold the TEMP 
button for 3 seconds. When adjust mode is activated, adjusting 
information will appear on the display screen. 

NOTE: To view Celsius temperatures, press the OPTIONS button 
when adjust mode is activated. To return the display setting to 
Fahrenheit, press OPTIONS again.

■

When adjust mode is activated, the display screen shows the 
refrigerator set point and “FRIDGE” appears. 

■

Press the DISPENSE TYPE  arrows to raise or lower the set 
point.

■

When you have finished viewing (and adjusting if desired) the 
refrigerator set point, press TEMP to change the display to 
show the freezer set point. When the zone has been changed, 
“FREEZER” appears on the display screen.

■

Press the DISPENSE TYPE  arrows to raise or lower the set 
point.

■

When you have finished viewing (and adjusting if desired) 
both the refrigerator and freezer set points, press LIGHT to 
save the settings.  

NOTE: To exit without saving changes, allow about 
60 seconds of inactivity and adjust mode will turn off 
automatically.

When adjusting temperature set points, use the following chart as 
a guide.      

The set point range for the refrigerator is 33°F to 45°F (0°C to 
7°C). The set point range for the freezer is -5°F to 5°F (-21°C to 
-15°C). 

REFRIGERATOR too cold

REFRIGERATOR Setting
1° higher 

REFRIGERATOR too warm 

REFRIGERATOR Setting
1° lower

FREEZER too cold

FREEZER Setting
1° higher

FREEZER too warm /
Too little ice

FREEZER Setting
1° lower