Heartland 311500L 설치 가이드

Due to continuing product improvements, Heartland Appliances reserves the right to amend specifica-

tions without notice. Please contact Heartland for the most up to date information, as it applies to product

being purchased, or download latest Site Preparation Specifications from www.heartlandapp.com.

Help Desk

877-650-5775

Heartland Appliances Inc. 1050 Fountain St North, Cambridge, ON, N3H 4R7

#02023
12-07-2006

©  2005 HEARTLAND APPLIANCES INC.

Appliance Clearances to allow proper air circulation,
plumbing and electrical connecitons (see Page 2 for
additional details):
•

Sides of refrigerator to adjacent surfaces: 1/4” (6 mm) min
per side.

•

Top: 1/2” (13 mm) minimum.

•

Rear clearance: 1/2” (13 mm) from cover plate (1” or 25
mm total)

•

Cut out height for refrigerator:
Option 1) without optional cowl: 70” (177.8 cm)
Option 2) with 6” high optional cowl: 76 (193.1 cm)

•

Cut out width for refrigerator’s main body: 36-1/2” (93 cm)

•

Max. cut-out depth: 24 1/2” (62 cm)

•

Note: If refrigerator is installed beside an appliance, it is
important that there be at least  5" (13 cm) between the
refrigerator and range for proper air circulation.

•

Electrical hookup must be performed by a licenced
electrician and outlet must be properly grounded.

•

Refrigerator must be plugged into its own individual
electrical outlet

•

115 Volts 60Hz 15 amps

•

Refrigerator must be electrically grounded in
compliance with local codes.  In the absence of local
codes, with the National Electrical code ANSI/NFPA 70
“Latest Edition” in the US or in Canada with the
Canadian Electrical Code, Part I, CSA Standard C22, or
the Local National Electrical Code.

•

Unit supplied with a 5 ft (1.5 m) power cord.

Electrical

How-to Steps

How-to Steps

Note: Ice maker factory installed on 36” models.

• AntiTip Bracket: Every refrigerator includes an

anti-tip bracket which must be properly in-
stalled to prevent  the refrigerator from tipping
forward should downward pressure be applied
with both doors open.

• To fasten bracket to the wall, distance from

floor to underside of bracket will be 68-3/4
(174.6 cm) min to 69-1/4 (176 cm) max. Mark
wall where studs are located.

• Slide unit into opening and raise back of unit by

turning 3/8” adjustors clockwise until unit is
snug against bracket (removing kickplate).

• Level front legs by turning two 3/8” adjustors

clockwise (accessible by removing kickplate).

• Once unit is in place, adjust both front “stability”

legs securely against floor.

Water Filter:
•

In-line water filter must be installed in
an accessible location to prevent dam-
age to refrigerator’s water solenoid.

Water

Shut Off Valve:
•

Shut off valve must be installed in an
accessible location for serviceability

Tubing Required:
•

Distance from the water valve at back of refrig-
erator to water supply pipe PLUS 8 feet (244 cm).

•

Excess tubing to be coiled into three 10” (25 cm)
diameter loops to allow refrigerator to move
away from wall after installation.

•

1/4” outer diameter copper Tubing (both ends of
tubing must be cut square).

•

Water pressure must be between 35-100 psi to
account for water filter

Safety

Corner Installations:
•

To allow door to open 90 degrees, corner
installations must allow 4” (10 cm) space be-
tween wall and refrigerator on hinge side. Filler
wood strip recommended for aesthetics.

Refrigerator

Water Valve

Location

Power Cord