Gaggenau AL400721 브로셔
104
Vario cooktops
V R 414 110
Stainless steel
Width 38 cm
Width 38 cm
Included in the price
1 lava stone
1 cleaning
1 cleaning
brush
2 cast
grills
1 grease collecting insert
1 Cast pan, half size
1 Cast pan, half size
Installation accessories
V A 420 010
V A 420 010
Connection strip for combination with
other Vario appliances of the 400
series for surface installation
other Vario appliances of the 400
series for surface installation
V A 420 011
Connection strip for combination with
other Vario appliances of the 400
series for surface installation with
appliance cover/adjustment strip
other Vario appliances of the 400
series for surface installation with
appliance cover/adjustment strip
V A 420 000
Connection strip for combination with
other Vario appliances of the 400
series for flush installation
other Vario appliances of the 400
series for flush installation
V A 420 001
Connection strip for combination with
other Vario appliances of the 400
series for flush installation with
appliance cover/adjustment strip
other Vario appliances of the 400
series for flush installation with
appliance cover/adjustment strip
V A 440 010
Stainless steel appliance cover with
mounting strip
mounting strip
V A 450 400
Stainless steel adjustment strip 38 cm
Required accessory for combination of
several Vario appliances of the 400
series with at least one appliance cover
to compensate the appliance depth.
Required accessory for combination of
several Vario appliances of the 400
series with at least one appliance cover
to compensate the appliance depth.
Special accessories
L V 030 000
L V 030 000
Lava stones for refilling
V A 461 000
Cast pan, enamelled, half size
For Vario electric grill 400 series.
For simultaneous frying and grilling on
two separate surfaces.
For Vario electric grill 400 series.
For simultaneous frying and grilling on
two separate surfaces.
V A 461 001
Cast pan, enamelled, full size
For Vario electric grill 400 series.
For frying large quantities on one
surface.
For Vario electric grill 400 series.
For frying large quantities on one
surface.
Vario electric grill 400 series
V R 414
– 2 separately controlled zones
– Cast pan, half size, for simultane-
ous frying and grilling on two
separate surfaces
separate surfaces
– Open cast grill, lava stones
– Solid stainless steel control knob
– Precision crafting of 3 mm stainless
steel
– For surface installation with a
visible edge or for flush installation
– Can be combined perfectly with
other Vario appliances of the 400
series
series
Handling
Control knobs with illuminated ring,
cooking zone and output level
markings.
Electronic control in 12 output levels.
cooking zone and output level
markings.
Electronic control in 12 output levels.
Features
Cooktop, lava stone trough and grease
collecting insert from stainless steel.
2 independently controlled grilling
elements (1,500 W).
Two-part cast grill.
collecting insert from stainless steel.
2 independently controlled grilling
elements (1,500 W).
Two-part cast grill.
Safety
Safety shut-off.
Planning notes
Depending on the type of installation
(surface-mounted or flush-mounted,
with or without an appliance cover), the
specific location of the cut-out and the
knob positions may vary.
If installing with the appliance cover
VA 440 or adjustement strip VA 450
take into account the additional space
required for the depth.
If combining several appliances with at
least one appliance cover, the
adjustment strip VA 450 is required to
compensate for the depth of the
appliance without the appliance cover.
If combining several Vario appliances
of the 400 series, a connection strip
VA 420 must be placed between the
appliances. Depending on the type of
installation, the corresponding
connection strip must be provided.
In the cut-out, the installation system
requires the side edge to be at least
10 mm for surface installation and at
least 13 mm for flush installation.
Ensure a continuous cut surface of
90°.
The bearing capacity and stability, in
the case of thin worktops in particular,
must be supported using suitable
substructures. Take into account the
appliance weight and additional loads.
Additional instructions for flush installa-
tion:
Installation is possible in worktops
made of stone, synthetics or solid
wood. Heat resistance and watertight
sealing of the cut edges must be
observed. Concerning other materials
please consult the worktop manu-
facturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the worktop cut-out.
(surface-mounted or flush-mounted,
with or without an appliance cover), the
specific location of the cut-out and the
knob positions may vary.
If installing with the appliance cover
VA 440 or adjustement strip VA 450
take into account the additional space
required for the depth.
If combining several appliances with at
least one appliance cover, the
adjustment strip VA 450 is required to
compensate for the depth of the
appliance without the appliance cover.
If combining several Vario appliances
of the 400 series, a connection strip
VA 420 must be placed between the
appliances. Depending on the type of
installation, the corresponding
connection strip must be provided.
In the cut-out, the installation system
requires the side edge to be at least
10 mm for surface installation and at
least 13 mm for flush installation.
Ensure a continuous cut surface of
90°.
The bearing capacity and stability, in
the case of thin worktops in particular,
must be supported using suitable
substructures. Take into account the
appliance weight and additional loads.
Additional instructions for flush installa-
tion:
Installation is possible in worktops
made of stone, synthetics or solid
wood. Heat resistance and watertight
sealing of the cut edges must be
observed. Concerning other materials
please consult the worktop manu-
facturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the worktop cut-out.
Please read additional planning notes
on page 116–123 .
on page 116–123 .
If installing several appliances in
individual cut-outs allow for a division
bar of minimum 50 mm between the
individual cut-outs.
Built-in control panel to be integrated
in the bottom cabinet at drawer level.
Panel thickness 16 – 26 mm.
The drawing "Installation of the control
knob" must be observed if the panel is
more than 26 mm thick (there must be
a recess at the rear).
A minimum lateral clearance of at least
100 mm from adjacent heat-sensitive
furniture or from the wall must be
observed.
Appliance can be snapped into the
worktop from above.
Appliance weight: approx. 26 kg.
individual cut-outs allow for a division
bar of minimum 50 mm between the
individual cut-outs.
Built-in control panel to be integrated
in the bottom cabinet at drawer level.
Panel thickness 16 – 26 mm.
The drawing "Installation of the control
knob" must be observed if the panel is
more than 26 mm thick (there must be
a recess at the rear).
A minimum lateral clearance of at least
100 mm from adjacent heat-sensitive
furniture or from the wall must be
observed.
Appliance can be snapped into the
worktop from above.
Appliance weight: approx. 26 kg.
Connection
Total connected load 3.0 kW.
Plan a connection cable.
Plan a connection cable.