Maytag MFX2570AEM 사용자 매뉴얼

■

Refrigerator air vent blocked? If the air vent located in the 
top, left, rear corner of the refrigerator compartment is 
blocked by items placed directly in front of it, the refrigerator 
will get too cold. Move items away from the air vent.

■

Ice storage bin in correct position? See “Ice Maker and Ice 
Storage Bin.” 

■

Controls set correctly for the surrounding conditions? 
Adjust the controls a setting warmer. Check temperature in 
24 hours. See “Using the Control(s).”

NOTE: Some moisture buildup is normal.

■

Humid room? Contributes to moisture buildup.

■

Door(s) opened often or left open? Allows humid air to 
enter refrigerator. Minimize door openings and keep doors 
fully closed. 

■

Refrigerator connected to a water supply and the supply 
shutoff valve turned on? Connect refrigerator to water 
supply and turn water shutoff valve fully open. 

■

Kink in the water source line? A kink in the line can reduce 
water flow. Straighten the water source line. 

■

Ice maker turned on? Make sure ice maker is on. See “Ice 
Maker and Ice Storage Bin.” 

■

New installation? Wait 24 hours after ice maker installation 
for ice production to begin. Wait 72 hours for full ice 
production.

■

Refrigerator door closed completely? Close the door 
firmly. If it does not close completely, see “The doors will not 
close completely.”

■

Large amount of ice recently removed? Allow 24 hours for 
ice maker to produce more ice. 

■

Ice cube jammed in the ice maker ejector arm?
Remove ice from the ejector arm with a plastic utensil.

■

Water filter installed on the refrigerator? Remove filter and 
operate ice maker. If ice volume improves, then the filter may 
be clogged or incorrectly installed. Replace filter or reinstall it 
correctly. 

■

Reverse osmosis water filtration system connected to 
your cold water supply? This can decrease water pressure. 
See “Water Supply Requirements.” 

NOTE: This is an indication of low water pressure.

■

Water shutoff valve not fully open? Turn the water shutoff 
valve fully open.

■

Kink in the water source line? A kink in the line can reduce 
water flow. Straighten the water source line. 

■

Water filter installed on the refrigerator? Remove filter and 
operate ice maker. If ice quality improves, then the filter may 
be clogged or incorrectly installed. Replace filter or reinstall it 
correctly. 

■

Reverse osmosis water filtration system connected to 
your cold water supply? This can decrease water pressure. 
See “Water Supply Requirements.”

■

Questions remain regarding water pressure? Call a 
licensed, qualified plumber.

■

New plumbing connections? New plumbing connections 
can cause discolored or off-flavored ice. 

■

Ice stored too long? Discard ice. Wash ice bin. Allow 
24 hours for ice maker to make new ice. 

■

Odor transfer from food? Use airtight, moisture proof 
packaging to store food. 

■

Are there minerals (such as sulfur) in the water? A water 
filter may need to be installed to remove the minerals. 

■

Water filter installed on the refrigerator? Gray or dark 
discoloration in ice indicates that the water filtration system 
needs additional flushing. Flush the water system before 
using a new water filter. Replace water filter when indicated. 
See “Water Filtration System.”

■

Refrigerator connected to a water supply and the supply 
shutoff valve turned on? Connect refrigerator to water 
supply and turn water shutoff valve fully open.

■

Kink in the water source line? Straighten the water source 
line. 

■

New installation? Flush and fill the water system. See “Water 
and Ice Dispensers.”

■

Is the water pressure at least 35 psi (241 kPa)? The water 
pressure to the home determines the flow from the dispenser. 
See “Water Supply Requirements.”

■

Water filter installed on the refrigerator? Remove filter and 
operate dispenser. If water flow increases, the filter may be 
clogged or incorrectly installed. Replace filter or reinstall it 
correctly.

■

Water dispenser measured fill feature is not dispensing 
an accurate amount of water? Calibrate the water 
dispenser. See “Water and Ice Dispensers.”