ONKYO PR-SC5507 사용자 설명서
130
Notes:
• Only analog input sources are output by the ZONE 2
• Only analog input sources are output by the ZONE 2
PRE OUT and ZONE 3 PRE OUT. Digital input
sources are not output. If no sound is heard when an
input source is selected, check if it’s connected to an
analog input.
sources are not output. If no sound is heard when an
input source is selected, check if it’s connected to an
analog input.
• You cannot select different AM or FM radio stations
for your main room and Zone 2/3. The same AM/FM
radio station will be heard in each room. For example,
if you have an FM station for the main room, that sta-
tion will also be used in Zone 2.
radio station will be heard in each room. For example,
if you have an FM station for the main room, that sta-
tion will also be used in Zone 2.
• When the input selector of Zone 2/3 is selected, power
consumption on standby mode slightly increases.
• While Zone 2/3 is on,
u functions will not work.
Adjusting the Volume for Zones
Muting Zones
Adjusting the Tone and Balance of Zones
Notes:
• Zones can also be unmuted by adjusting the volume.
• The volume, tone and balance functions cannot be set
• Zones can also be unmuted by adjusting the volume.
• The volume, tone and balance functions cannot be set
when the “Zone2 Out” or “Zone3 Out” setting is set to
“Fixed” (page 128).
“Fixed” (page 128).
• Even if you repeatedly press the remote controller’s
[ZONE] button to select zones, the last zone selection
will be retained once you have switched to other com-
ponents by pressing other REMOTE MODE buttons
after pressing the [ZONE] button.
will be retained once you have switched to other com-
ponents by pressing other REMOTE MODE buttons
after pressing the [ZONE] button.
Remote
controller
On the remote controller, press
the [ZONE] button repeatedly,
and then use the VOL [
the [ZONE] button repeatedly,
and then use the VOL [
q]/[w]
button.
AV controller
On the AV controller, press the
[ZONE 2] or [ZONE 3] button (the
ZONE 2/3 indicator and Zone 2/3
selector on the display flashes)
and press [LEVEL] button
followed by the Up [
[ZONE 2] or [ZONE 3] button (the
ZONE 2/3 indicator and Zone 2/3
selector on the display flashes)
and press [LEVEL] button
followed by the Up [
r] and Down
[
e] buttons within 8 seconds.
Remote
controller
On the remote controller, press
the [ZONE] button repeatedly,
and then press the [MUTING]
button.
the [ZONE] button repeatedly,
and then press the [MUTING]
button.
To unmute a zone, on the remote
controller, press the [ZONE]
button, and then press the
[MUTING] button again.
controller, press the [ZONE]
button, and then press the
[MUTING] button again.
1
AV controller
On the AV controller, press the
[ZONE 2] or [ZONE 3] button.
[ZONE 2] or [ZONE 3] button.
2
Press the AV controller’s [TONE]
button repeatedly to select
“Bass”, “Treble” or “Balance”.
button repeatedly to select
“Bass”, “Treble” or “Balance”.
3
Use the Up [
r] and Down [e]
buttons to adjust the bass, treble
or balance.
• You can boost or cut the bass or tre-
or balance.
• You can boost or cut the bass or tre-
ble from –10 dB to +10 dB in 2 dB
steps.
steps.
• You can adjust the balance from 0 in
the center to +10 dB to the right or
+10 dB to the left in 2 dB steps.
+10 dB to the left in 2 dB steps.