Maytag W10321481A 사용자 설명서

다운로드
페이지 58
7
  Crisper Humidity Control 
(on some models)
You can control the amount of humidity in the moisture-sealed 
crisper. Adjust the control to any setting between LOW and 
HIGH.
LOW (open) for best storage of fruits and vegetables with skins. 
HIGH (closed) for best storage of fresh, leafy vegetables. 
Chilled Door Bin
(on some models)
Cool air from the freezer is directed to the refrigerator door bin 
directly beneath the vents.
NOTE: The dairy compartment and can rack are not associated 
with the Chilled Door Bin feature.
Chilled Door Bin Control
The chilled door bin control is located on the left-hand side of the 
refrigerator compartment.
Slide the door chill control to the left or down to reduce the 
flow of cold air to the bin and make it less cold. 
Slide the door chill control to the right or up to increase the 
flow of cold air to the bin and make it colder.
Water and Ice Dispensers
(on some models)
Depending on your model, you may have one or more of the 
following options: the ability to select either crushed or cubed 
ice, a special light that turns on when you use the dispenser, or a 
lock option to avoid unintentional dispensing.
IMPORTANT: After connecting the refrigerator to a water source 
or replacing the water filter, flush the water system. Use a sturdy 
container to depress and hold the water dispenser lever for 
5 seconds, then release it for 5 seconds. Repeat until water 
begins to flow. Once water begins to flow, continue depressing 
and releasing the dispenser lever (5 seconds on, 5 seconds off) 
until a total of 3 gal. (12 L) has been dispensed. This will flush air 
from the filter and water dispensing system, and prepare the 
water filter for use. Additional flushing may be required in some 
households. As air is cleared from the system, water may spurt 
out of the dispenser. 
NOTES:
The dispensing system will not operate when the freezer door 
is open.
Allow 24 hours for the refrigerator to cool down and chill 
water.
Allow 24 hours to produce the first batch of ice. Discard the 
first three batches of ice produced.
The display screen on the dispenser control panel has a 
backlight, which will turn off automatically when the control 
buttons have not been used for 30 seconds or more. When 
the backlight is off, the first press of a control button will only 
reactivate the backlight, without changing any settings. 
Within 30 seconds after the backlight has been reactivated, 
additional presses of control buttons will change the 
applicable settings.
The Water Dispenser
IMPORTANT: Dispense enough water every week to maintain a 
fresh supply.
Water Dispenser Buttons and Pad
There are three dispenser panel buttons primarily used in the 
water dispensing process: 
In the row of six buttons below the dispenser display screen, 
the fourth button (from the left) is the WATER selection 
button. It is used to select water instead of ice for dispensing.
Centered below the row of six buttons is the WATER 
dispenser button. This is used to actually dispense water.
In the row of six buttons, the fifth button (from the left) is the 
MEASURE FILL button. This activates the Measured Fill 
feature.     
The dispenser pad is located on the back wall of the dispenser 
cavity. When pressed, either water or ice will dispense, 
depending on the chosen setting.
To Dispense Water (Standard):
1. To select water, press the WATER selection button. The 
display screen will indicate when water is selected.
2. Press a sturdy glass against the dispenser pad OR place the 
glass below the water dispenser and press the WATER 
dispenser button.
3. Remove the glass OR release the button to stop dispensing.
NOTE: While dispensing water and for 5 seconds after 
dispensing has stopped, the digital display will show how 
much water has been dispensed. 
A. Chilled door bin control
A
A. WATER selection button
B. WATER dispenser button
C. MEASURE FILL button
A B
C