Vermont Casting LHECDV20 사용자 설명서

3

This gas appliance should be installed by a qualified installer in 
accordance with local building codes and with current CSA-
B149.1 Installation codes for Gas Burning Appliances and 
Equipment. FOR U.S. Installations follow local codes and/or the 
current National Fuel Gas Code ANSI Z223.1/NFPA 54.
In the Commonwealth of Massachusetts, all gas fittings and 
installation of this heater shall only be done by a licensed gas 
fitter or licensed plumber.

FOR SAFE INSTALLATION AND OPERATION OF YOUR 
GAS FIREPLACE PLEASE NOTE THE FOLLOWING:

1.  This appliance gives off high temperatures and should be 

located out of high traffic areas and away from furniture and 
draperies.

2.  Children and adults should be alerted to the hazards of the 

high surface temperatures of this appliance and should stay 
away to avoid burns or ignition of clothing.

3.  Children should be carefully supervised when they are in the 

same room as your appliance.

4.  Under no circumstances should this appliance be modified. 

Parts removed for servicing should be replaced prior to 
operating this appliance again.

5.  Installation and any repairs to this appliance should be car-

ried out by a qualified service person. A professional service 
person should be contacted to inspect this appliance an-
nually. Make it a practice to have all of your gas appliances 
checked annually.  More frequent cleaning may be required 
due to excess lint and dust from carpeting, bedding material, 
etc.

6.  Control compartments, burners and air passages in this ap-

pliance should be kept clean and free of dust and lint. Make 
sure that the gas valve and pilot light are turned off before 
you attempt to clean this unit.

7.  The venting system (chimney) of this appliance should be 

checked at least once a year and if needed your venting 
system should be cleaned.

8.  Keep the area around your appliance clear of combustible 

materials, gasoline and other flammable vapor and liquids. 
This appliance should not be used as a drying rack for cloth-
ing, nor should Christmas stockings or decorations be hung 
in the area of it.

9.  Under no circumstances should any solid fuels (wood, coal, 

paper or cardboard etc.) be used in this appliance.

10. Whether the zero clearance kit is installed directly on carpet-

ing, vinyl tile or any combustible material other than wood, 
this heater must be installed on a metal or wood panel 
extending the full width and depth of the heater. The insert 
can not be installed directly onto or into combustibles.

It is normal for fireplaces fabricated of steel to give off some 
expansion  and/or  contraction  noises  during  the  start  up  or 
cool down cycle.  Similar noises are found with your furnace 
heat  exchanger or car engine.
It is not unusual for your gas fireplace to give off some odor 
the first time it is burned.  This is due to the curing of the paint 
and any undetected oil from the manufacturing process.

It is recommended that you burn your fireplace for at least ten 
(10) hours the first time you use it.  If optional fan kit has been 
installed, place fan in the "OFF" position during this time.

Proposition 65 Warning: Fuels used in gas, wood-
burning or oil fired appliances, and the products of 
combustion of such fuels, contain chemicals known to 
the State of California to cause cancer, birth defects 
and other reproductive harm.
California Health & Safety Code Sec. 25249.6

FP1249a

locating DV unit

with zero clearance kit

4/03

FP1249a

Fig. 1  Locating unit with zero clearance kit.

 

A)   Flat on wall  

B)   Cross corner

 

C)   Island 

D)   *Room divider

 

E)   *Flat on wall corner 

F)   Chase installation

NOTE: (Fig. 1)
*  When you install your fireplace in (D) Room divider or (E) Flat 
on  wall  corner  positions,  a  minimum  of  6  (X)  inches  (153mm) 
clearance must be maintained from the perpendicular wall and 
the outer edge of the trim.

Before installing the gas fireplace insert, consideration must 
be given to the functioning needs of the fireplace.  The size 
of the fireplace cavity (min. 25¹⁄₄"W x  17¹⁄₂"H x 13¹⁄₂" D (641 x 
438 x 343 mm) for the LHECDV20 and LHERDV20, 28³⁄₄"W 
x 21"H x 15¹⁄₂"D (730 x 533 x 394 mm) for LHECDV30 and 
LHERDV30), the design of the chimney for effective venting 
should be determined. The availability of the gas supply as well 
as electricity for the insert fan must be confirmed.

This appliance may be installed in an aftermarket per-
manently located, manufactured (mobile) home, where 
not prohibited by local codes.
This appliance is only for use with the type of gas indi-
cated on the rating plate.