Franke Consumer Products FHPL 301 1CO 사용자 설명서

11

Note
The cooking zone appears incandescent until the heat level corresponding to the selected power is reached; when 
the level is reached, an electronic device deactivates and activates the heating element to keep the temperature 
constant. The heating element will be alternately incandescent or switched off.

After switching on, the control panel remains activated for 10 seconds; the hob switches off automatically if 
no cooking zone is selected.
If a cooking zone is selected but without increasing the power, after 10 seconds the zone is automatically 
deselected and the hob switches off after another 10 seconds.

Activate the control zone with the selection button

. By pressing the buttons 

 and 

 at the same time, 

the power level of the zone will be brought to 0. Alternatively, the button 

 can be used to decrease the 

power level to 0. The outer circuit can be switched off separately from the inner circuit by pressing the button 

, after reactivating the control zone by pressing the button 

 .

Both circuits can be immediately switched off at any time by means of the 
ON/OFF 

 button; an “H” appears if the cooking zone is still hot. The ON/OFF button 

 is always active, 

even if the control panel lock (child safety device) has been set.

It starts the cooking, exploiting the maximum power, and then 
automatically reduces it to the required level.
When the automatic preheating function is activated, the power of 
the cooking zone is at 100% for a given time that depends on the 
power level selected (see table opposite, column AHT). At the end 
of the heat-up time the cooking zone returns to the preset power 
level.
To activate automatic heat-up, proceed as follows:
• with the hob switched on, activate the control zone;
• when power level 9 is reached, automatic heat-up is activated by 

immediately pressing the button 

 again, and the symbol “A” 

appears on the display;

• then select the power level required for cooking, using the 

button 

 and possibly the button 

. The display will show the 

selected level;

• after a few seconds the symbol “A” will appear on the display, 

alternating with the selected power level. At the end of the 
automatic heat-up stage (see table opposite) the display will only 
show the preset power level;

• to increase the preset power, 

 press the button; in which case the automatic heat-up time will be 

adapted to the selected setting;

• This function can be stopped by pressing the button 

, a few seconds after the “A” appears on the display.

After switching off the cooking zone, the corresponding display shows “H”, indicating that the glass surface is 
still hot, until the temperature of the zone falls below the critical level (approx. 60°C). During this stage do 
not clean or touch the cooking zones.

In relation to the power level, each cooking zone is switched off after a max. set time if no operation is carried 
out (see the table above, column OTL).
Every operation on the cooking zone by means of the buttons 

 and 

 resets the maximum operating time 

of the zone to its max. value.

The hob has several systems that protect against possible overheating which could damage the electronic 
components. If the cooking zone is switched on without placing a pot on it, the power is automatically 
reduced to minimum. If the cooking zone is used at high power for a long time, the hob automatically 
switches off and error code E2 appears (see the section “Support”). Therefore prolonged use at high power 
is inadvisable.

AHT = Automatic Heat Up Time
OTL = Operating Time Limitation

power

level.

Power 

(%)

AHT

(s)

OTL 

(min)

1

3

60

360

2

6.5

180

360

3

11

288

300

4

15.6

390

300

5

19

510

240

6

31.8

210

90

7

45.1

210

90

8

64.5

270

90

9

100

---

90