Porter-Cable FTS-150 사용자 설명서
10
MANDATORY
INDICATION
INFORMATION
INSTRUCTION
INFORMATION
INSTRUCTION
WARNING
PROHIBITION
These signs will give
advise for your safety
Before leaving our factory every machine
is thoroughly tested.
Follow our instructions strictly and your machine
will give you long service in normal operating
conditions.
will give you long service in normal operating
conditions.
1. Features
Use: Sawing of any kind of tile, up to 19”
(482mm); diagonal of 13” x 13” (330 x 330mm) tile.
Tools: All accessories come standard with your saw;
(482mm); diagonal of 13” x 13” (330 x 330mm) tile.
Tools: All accessories come standard with your saw;
including a 10” (254mm) continuous rim
Diamond Blade & Multi-Wrench
Diamond Blade & Multi-Wrench
Blade Capacity: Ø 10
″
(250 mm)
Bore 5/8
″
(15.9 mm).
Blade Rotation: Counter-Clockwise (CCW).
Depth of Cut: 3-1/4
Depth of Cut: 3-1/4
″
(83mm)
Cutting Length: 19
″
(48.3cm)
Blade Cooling: Water pump
Horsepower: 1-1/2
Voltage: 120 Volts, 60 Hertz, 1-Phase
Amperage: 15 amps (Full Load)
Blade Shaft RPM: 2800
Weight lbs. (kg.): 112 (50.8)
Dimensions (L x W x H): 39-3/4
Horsepower: 1-1/2
Voltage: 120 Volts, 60 Hertz, 1-Phase
Amperage: 15 amps (Full Load)
Blade Shaft RPM: 2800
Weight lbs. (kg.): 112 (50.8)
Dimensions (L x W x H): 39-3/4
″
x 22
″
x 20-1/2
″
(101 x 55.9 x 52.1cm)
Pan Holding Capacity: 5.3 gallons (20 liters)
Before starting up the machine, make sure
you read this entire manual and are familiar
with the operation of this machine.
The working area must be completely clear,
well lit and all safety hazards removed.
you read this entire manual and are familiar
with the operation of this machine.
The working area must be completely clear,
well lit and all safety hazards removed.
The operator must
wear protective
clothing appropriate
to the work he is
doing.
wear protective
clothing appropriate
to the work he is
doing.
Any persons not involved in the work
should leave the area.
Use only blades marked with a maximum
speed greater than the blade shaft
speed.
speed greater than the blade shaft
speed.
2. Benefits
Your FELKER
tile saw is a ruggedly constructed unit
engineered to give long, satisfactory performance.
Simple, daily maintenance and care will add to the life
and productivity of your tile saw.
Simple, daily maintenance and care will add to the life
and productivity of your tile saw.
•
Full 1-1/2 HP, 115V/60/1 motor for powerful cuts.
•
Has a durable polymer cutting table – able to
handle almost any cutting job due to its reinforced
construction.
handle almost any cutting job due to its reinforced
construction.
•
Removable extension can also be fastened to
side of cart for holding wide material.
side of cart for holding wide material.
•
Cutting table designed to drain water quickly back
into the water tray for efficient recycling of water.
into the water tray for efficient recycling of water.
•
Cast blade guard will hinge to allow easy removal
of cutting blade. Accepts up to 12” diameter
blade.
of cutting blade. Accepts up to 12” diameter
blade.
•
Cutting table runs on nylon wheels for smooth
and accurate cuts and easy maintenance.
and accurate cuts and easy maintenance.
•
Water tray of durable polymer construction to
resist rust and to drain water and sediment much
faster.
resist rust and to drain water and sediment much
faster.
3. Machine
Set-Up
Follow all of the assembly and
installation instructions completely
before connecting this saw to a power
source.
installation instructions completely
before connecting this saw to a power
source.
UNPACKING
(Fig 1 – page 11 & Fig’s 3 & 4 – page 12)
Carefully open the container and remove all the saw
components and packing materials. Be certain you
have checked each item with the checklist below
before discarding the container or the packing
materials. The contents are as follows:
components and packing materials. Be certain you
have checked each item with the checklist below
before discarding the container or the packing
materials. The contents are as follows:
1. Operator’s Manual 6. Blade – 10” [250mm]
2. Cutting Head Assy 7. Water Pump, 115V/60
3. Frame w/Cart
2. Cutting Head Assy 7. Water Pump, 115V/60
3. Frame w/Cart
8. Motor Support Shaft
4. Water Tray
9. Multi-Wrench
5. Blade Guard
10. Rip Guide
11. Accessories: Cart Extension, Bullnose Miter, Dual
45
45
°
Miter & Adj. Protractor
NOTE: IF ANY OF THE PARTS ARE MISSING OR
DAMAGED PLEASE CONTACT YOUR FELKER
CUSTOMER SERVICE FOR INSTRUCTIONS.
CALL 1-800-365-4003
DAMAGED PLEASE CONTACT YOUR FELKER
CUSTOMER SERVICE FOR INSTRUCTIONS.
CALL 1-800-365-4003