Samsung CLX-3175FN 사용자 설명서

Getting started_ 26

You need to set up the network protocols on the machine to use it in the 

network environment. You can set up the basic network settings through the 

machine's control panel.

The following table shows the network environments supported by the 

machine:

You can set up TCP/IP network parameters, follow the steps listed below. 
1. Make sure your machine is connected to the network with an RJ-45 

Ethernet cable.

2. Make sure you have turned on the machine.
3. Press Menu and then OK.
4. Press the left/right arrow until Network appears and press OK.
5. Press the left/right arrow until TCP/IP appears and press OK.
6. Press the left/right arrow until Static appears and press OK.
7. Press the left/right arrow until IP Address appears and press OK.

Enter a byte between 0 and 255 using the left/right arrow and press OK.

Repeat this to complete the address from the 1st byte to the 4th byte.

8. Repeat steps 7 to configure the other TCP/IP parameters: subnet mask 

and gateway address.

9. Press Stop/Clear to return to ready mode.

This program is for the network IP setting using the MAC address which is 

the hardware serial number of the network printer card or interface. 

Especially, it helps the network administrator set several network IPs at the 
same time. 

1. Insert the driver CD provided along with your machine. When the driver 

CD runs automatically, close the window.

2. Start Windows Explorer and open the X drive. (X represents your CD-

ROM drive.)

3. Double-click Application > SetIP.
4. Double-click Setup.exe to install this program.
5. Click OK.

If necessary, select a language from the drop-down list.

6. Follow the instructions in the window and complete the installation.

1. Print the machine’s network configuration report to find your machine’s 

MAC address. See "Printing reports" on page 46.

2. From the Windows Start menu, select All Programs > Samsung 

Network Printer Utilities > SetIP > SetIP.

3. Click 

 to open the TCP/IP configuration window.

4. Enter the network card's MAC address, IP address, subnet mask, 

default gateway, and then click Apply.

5. Click OK, then the machine prints the network information. Confirm the 

settings are correct.

6. Click Exit.

•

Ethernet 10/100 Base-TX

•

Windows 2000/XP/2003/Vista

•

Various Linux OS

•

MAC OS 10.3 ~ 10.5

•

TCP/IP

•

Standard TCP/IP

•

LPR

•

IPP/HTTP

•

Bonjour

•

DHCP

•

BOOTP

http://developer.apple.com/

networking/bonjour/download/

, select the program Bonjour for 

Windows due to your computer operating system, and install the 

program. This program will allow you to fix the network parameter 

automatically. Follow the instruction in the installation window. This 
Bonjour program does not support Linux.

Contact the network administrator if you are not sure how to configure.

You can also set up the network settings through the network 

administration programs. 

•

SyncThru™ Web Admin Service: Web-based printer 

management solution for network administrators. SyncThru™ 

Web Admin Service provides you with an efficient way of 

managing network devices and lets you remotely monitor and 

troubleshoot network machines from any site with corporate 
internet access. Download this program from 

.

•

SyncThru™ Web Service: Web server embedded on your 

network print server, which allows you to:

- Configure the network parameters necessary for the machine to 

connect to various network environments.

- Customize machine settings.

•

SetIP: Utility program allowing you to select a network interface 

and manually configure the IP addresses for use with the TCP/IP 

protocol. (See "Using the SetIP program" on page 26.)

•

You can only use SetIP program when your machine is connected 

to a network.

•

The following procedure is based on windows XP. If you use 

Macintosh or Linux OS, see Software section

when you enter the MAC address, enter it without colon(:).