JVC DLA-M2000LU 사용자 설명서

No.51781

1-23

DLA-M2000LU

DLA-M2000LE

Basic Operations 

■

While projecting an image, a still picture is obtained at any 
time by using the FREEZE button on the remote control.

“FREEZE” appears on the screen for a few seconds and 
then the still picture is shown on the screen. Refer to the 
FREEZE message shown on the left of this page.

* To forcibly clear “FREEZE”, press the ESCAPE button.

The original image resumes.

• During freezing, the picture sent from the signal source is lost.
• If any of the inoperative buttons (“MENU”, “QUICK ALIGN.”, 

“KEYSTONE”) are pressed while displaying a still picture, 
“FREEZE” is displayed on the screen.

• This function will not work with some signal sources 

(UXGA, etc). In this case, the FREEZE inhibit message 
appears for a few seconds, as shown on the left. To forcibly 
clear this message, press the ESCAPE button.

A part of the image being projected can be digitally magnified up 
to four times. When the DIGITAL ZOOM + or – button is 
pressed, “Digital zoom” appears on the screen together with the 
level bar and magnifying power (

×

1.0, 

×

1.2, 

×

1.4, 

×

1.6, 

×

2.0, 

×

2.5, 

×

3.2, 

×

4.0). When “15 sec.” is displayed in the menu, 

“Digital zoom” will appear in approximately 15 seconds.

• To zoom up or zoom down, press the DIGITAL ZOOM + or 

– button on the remote control.

While “Digital zoom” appears on the screen, you can move 
the zoomed image with the cursor (

5

/

∞

/

2

/

3

)/ENTER button 

on the remote control.

5

: Upper part of the image will be

displayed.

∞

: Lower part of the image will be

displayed.

2

: Left side part of the image will

be displayed.

3

: Right side part of the image

will be displayed.

• This function will not work with some signal sources 

(UXGA, etc). In this case, the DIGITAL ZOOM inhibit 
message appears for a few seconds, as shown on the left. To 
forcibly clear this message, press the ESCAPE button.

• The quality of the zoomed image reduces in comparison 

with the original one.

• To return to the original size (

×

1.0) and original position, 

press the PRESET button while “Digital zoom” is displayed 
on the screen.

U

T

D

W

FOCUS

–

+

ZOOM

SHIFT

VOLUME

–

+

QUICK

ALIGN.

SHUTER

–

+

EN

T

E

R

HIDE

OPERATE

PRESET

ESCAPE

DIGITAL

ZOOM

KEYSTONE

PC

+

–

VIC SELECT

MENU

FREEZE

VIDEO

RM-M2000  REMOTE  CONTROL  UNIT

FREEZE

button

PRESET

button

ESCAPE

button

DIGITAL ZOOM

+/-button

Cursor
 (

5

/

∞

/

2

/

3)/

ENTER button

Digital zoom

1.2

+

–

EN

TE

R

You can adjust picture quality, set functions, get information on the input video signal, etc. using the menus. From the 
following menu transition diagrams, you can see the overall menus and basic button operation in menu mode. Note that there 
are three menu modes, No signal menu mode, video menu mode and PC menu mode. When the MENU button is pressed, 
the projector enters one of  these modes by judging the input signal being received.

■

This is displayed if there is no signal from the selected input terminal.

■

Main Menu in No signal Menu Mode

Options

Right Left rev.:

OFF* / ON (Select for upside-down hanging on the ceiling.)

Top Bottom inv.:

OFF* / ON (Select for upside-down hanging on the ceiling.) 

RS-232C [bps]:

Selectable baud rate (transmission speed). 9600 / 19200*

Sleep time [min:]

Selectable sleep times. If no-signal condition continues for the period of selected time (Unit: 
Minutes), the projector enters the stand-by mode. 15 / 30 / 60 / OFF*

PC2 (BNC):

RGB* or YP

B

P

R

. Set to RGB when a computer device with analog RGB, V, H/Cs signals is 

connected to the PC2 terminals. Set to YP

B

P

R

 when a device with component signals (Y, B-Y, R-Y) 

or DTV-format signals (Y, P

B

, P

R

) are connected to the PC2 terminals.

Language

Language for on-screen display.

Japanese / English* / German / Spanish / Italian / French

Information

Input:

Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO, or PC2)

Switcher:

Has no meaning. This display currently has no meaning. (“CH.0” is usually displayed to indicate 
that it is not being used.)

Lamp time:

Accumulated used hours of the light-source lamp.

RGB

YP

B

P

R

Menu

Options

Language

Information

English

Deutsch

Español

Italiano

Français

Menu

Options

Language

Information

Input

Switcher

Lamp time

PC1

CH.0

123 h

Language

Options

Right Left rev. 

Top Bottom inv. 

RS-232C [bps] 

Sleep time [min] 

PC2 (BNC)

OFF

OFF

9600

ON

ON

19200

15

30

60

OFF

English

Deutsch

Español

Italiano

Français

Menu

Options

Language

Information

Right Left rev.

Top Bottom inv.

RS-232C

Sleep time

PC2 (BNC)

Press 

5/∞ to select an item.

Press 

5/∞ to select an item.

Press 

2/3 to set the value.

Press 

5/∞ to select an item.

3 or ENTER

ESCAPE

3 or
ENTER

ESCAPE

∞

5

∞

5

∞

5