Netgear WNDAP360-100NAS 전단

This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste 

Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union, 

this product should be treated and recycled in accordance with the laws of your jurisdiction 

implementing the WEEE Directive.

©2011 by NETGEAR, Inc. All rights reserved. NETGEAR, the NETGEAR logo, and ProSafe® are registered 

trademarks of NETGEAR, Inc. in the United States and/or other countries. Other brand and product names are 

trademarks or registered trademarks of their respective holders. Information is subject to change without notice. 

Using a computer with an 802.11b/g/n wireless adapter, verify connectivity by using 
a browser to connect to the Internet, or check for file and printer access on your 
network.

If you cannot connect, see Troubleshooting Tips in this guide or the 

Reference Manual.

To use an external 2.4 GHz antenna:

Mount the accessory antenna(s).

Attach the antenna(s) to the connector(s) on the access point rear panel.

Log into the access point and configure it to use the external antenna. The 

access point cannot use the internal and external 2.4GHz antennas at the 

same time. 

Here are some tips for correcting simple problems you may have.

The wireless access point has no power.

Make sure the power cord is connected to the wireless access point and 

plugged in to a working power outlet or power strip.

Make sure you are using the correct NETGEAR power adapter supplied with 

your wireless access point.

If using PoE, ensure that the PoE switch is providing power to the access point.

There is a hardware connection problem.

Make sure the cable connectors are securely plugged in to the access point and 

to the network device (hub, switch, or router).

Make sure the connected device is turned on. If the Ethernet link is a 10 Mbps 

link, then the 10/100/1000 light is off, but the Link/Act light blinks if traffic is 
present.

The wireless connection is not working.

If a Wireless LAN activity LED stays off, disconnect the power adapter from its 

power source and then plug it in again. 

Log in to the access point and verify that the radio is turned on.

Contact NETGEAR if the Wireless LAN LED remains off.

Check these items:

The access point is correctly installed, it is powered on, and LAN connections 

are OK. Check that the LAN LED is on to verify that the Ethernet connection is 
OK.

If you are using the Net BIOS name of the access point to connect, ensure that 

your PC and the access point are on the same network segment or that there is 
a WINS server on your network.

If your PC uses a fixed (static) IP address, ensure that it is using an IP address 

in the range of the access point. The access point default IP address is 
192.168.0.100 and the default subnet mask is 255.255.255.0. The access point 
default setting is for a static IP address. If the network where you are connecting 
it is using DHCP, configure it accordingly. See the Reference Manual for details.

There is a configuration problem. Check these items:

You might not have restarted the computer with the wireless adapter to have 

TCP/IP changes take effect. Restart the computer.

The computer with the wireless adapter might not have the correct TCP/IP 

settings to communicate with the network. Restart the computer and check that 
TCP/IP is set up correctly for that network. The usual setting for Windows on the 
Network Properties is set to “Obtain an IP address automatically.”

The wireless access point’s default values might not work with your network. 

Check the wireless access point default configuration against the configuration 
of other devices in your network.

For full instructions on changing the default values of the wireless access point, 

see the Reference Manual.

In the interest of improving internal design, operational function, and/operability, 
NETGEAR reserves the right to make changes to the product described in this 
document without notice. NETGEAR does not assume any liability that may occur 
due to the use or application of the product(s) or circuit layout(s) described herein.

Thank you for selecting NETGEAR products.

After installing your device, locate the serial number on the label of your product and 
use it to register your product at 

. Registration is 

required before you can use our telephone support service. Registration via our web 
site is strongly recommended. 

Go to 

 for product updates and Web support. For 

Warranty and Regional Customer Support information, see the Resource CD that 
came with your product.

For complete DoC please visit the NETGEAR EU Declarations of Conformity 
website at: 

WNDAP360_IG_3Mar2011.fm  Page 2  Thursday, March 3, 2011  2:47 PM