Troy-Bilt J609 사용자 설명서
11
Ammeter
The ammeter measures the
electrical output of the engine’s
charging system. Under
normal operating conditions,
with engine at full throttle, the
ammeter should indicate
positive charge.
electrical output of the engine’s
charging system. Under
normal operating conditions,
with engine at full throttle, the
ammeter should indicate
positive charge.
PTO (Blade Engage) Lever
The PTO (Blade Engage) lever is located on the left
side of the dashboard next to the steering wheel. Move
the PTO (Blade Engage) lever forward to engage the
power to the cutting deck or other (separately available)
attachments; move the PTO (Blade Engage) lever
rearward to disengage the power to the attachments.
side of the dashboard next to the steering wheel. Move
the PTO (Blade Engage) lever forward to engage the
power to the cutting deck or other (separately available)
attachments; move the PTO (Blade Engage) lever
rearward to disengage the power to the attachments.
NOTE:
The PTO (Blade Engage) lever must be in the
disengaged (OFF) position when starting the engine,
when traveling in reverse and if the operator leaves the
seat.
when traveling in reverse and if the operator leaves the
seat.
Seat Adjustment Lever
To adjust the seat position, loosen the two seat
adjustment knobs and reposition the seat to the desired
position. Once a comfortable position is found, tighten
the adjustment knobs to lock the seat in place. Refer to
Seat Adjustment on page 17 of this manual for more
detailed instructions.
adjustment knobs and reposition the seat to the desired
position. Once a comfortable position is found, tighten
the adjustment knobs to lock the seat in place. Refer to
Seat Adjustment on page 17 of this manual for more
detailed instructions.
Deck Lift Lever
Found on your tractor’s right fender, the deck lift lever is
used to change the height of the cutting deck. To use,
move the lever to the left, then place in the notch best
suited for your application.
used to change the height of the cutting deck. To use,
move the lever to the left, then place in the notch best
suited for your application.
Parking Brake Button
To set the parking brake, fully depress
the brake pedal and push the parking
brake button in. Hold the button in while
taking your foot off the brake pedal.
Both the parking button and the brake
pedal will then stay depressed. To
release the parking brake, depress the
brake pedal slightly. The parking brake
button will then return to its original
position.
the brake pedal and push the parking
brake button in. Hold the button in while
taking your foot off the brake pedal.
Both the parking button and the brake
pedal will then stay depressed. To
release the parking brake, depress the
brake pedal slightly. The parking brake
button will then return to its original
position.
NOTE:
The parking brake must be set if the operator
leaves the seat with the engine running or the engine
will automatically shut off.
will automatically shut off.
IMPORTANT:
Always set the parking brake when
leaving the tractor unattended.
Cruise Control Button
The cruise control button is
located on the tractor dash panel
to the left of the ignition switch.
Push the cruise control button
while traveling forward at a
desired speed. While holding the
button in, release pressure from
the drive pedal. This will engage
the cruise control and allow the
tractor to remain at that speed
without applying pressure to the drive pedal. Depress
the brake pedal or the drive pedal to deactivate cruise
control. Refer to Setting the Cruise Control on page 14 this
manual for detailed instructions regarding the cruise
control feature.
located on the tractor dash panel
to the left of the ignition switch.
Push the cruise control button
while traveling forward at a
desired speed. While holding the
button in, release pressure from
the drive pedal. This will engage
the cruise control and allow the
tractor to remain at that speed
without applying pressure to the drive pedal. Depress
the brake pedal or the drive pedal to deactivate cruise
control. Refer to Setting the Cruise Control on page 14 this
manual for detailed instructions regarding the cruise
control feature.
NOTE:
Cruise control can NOT be engaged at the
tractor’s fastest ground speed. If the operator should
attempt to do so, the tractor will automatically
decelerate to the fastest optimal mowing ground speed.
attempt to do so, the tractor will automatically
decelerate to the fastest optimal mowing ground speed.
Shift Lever
The shift lever is located on the left side of the fender
and has three positions, FORWARD, NEUTRAL and
REVERSE. The brake pedal must be depressed and
the tractor must not be in motion when the moving shift
lever. See Figure 6.
and has three positions, FORWARD, NEUTRAL and
REVERSE. The brake pedal must be depressed and
the tractor must not be in motion when the moving shift
lever. See Figure 6.
Figure 6
IMPORTANT:
Never force the shift lever. Doing so may
result in serious damage to the tractor’s transmission.
A M PS
04/
ON
OFF
PTO
P
N
F
R
Shift Knob