Marshall electronic V-R1042DP-TE4U 사용자 설명서
Marshall Electronics
4
5
Electrical Specifications
Display (Viewing Area)
10.4 Inch diagonal (211.2mm W x 158.4mm H)
Screen Aspect
Native 4:3, Switchable to 16:9
Resolution (RGB Dots)
1024HxRGx768V (2.4 Million Pixels)
Viewing Angles
170°H x 170°V
Contrast Ratio
400:1
Dot Pitch
0.206mm square pixel
Pixel Response
13ms rise /12ms fall
Brightness
400 cd/m²
Backlight
Field Replaceable CCFL (50,000 hour half life)
Screen Treatments
Anti Reflection, Anti Glare, Hard Coat
Protective Screen
0.118” (3mm) thick Optical Grade Polycarbonate with Anti-Glare and Anti-Abrasion
coatings. (600 Cheesecloth mil-M-13508C)
Estimated MTBF
5 years of 24/7 operation
Inputs
1 SDI/HDSDI input per screen; SMPTE 259M-C, 292M / ITU-R BT.601; female BNC;
1080i/60,59.95,50; 1080psF/24,23.98; 1035i/60,59.94; 720p/60,59.94,50,30,29.97,25
Active Outputs
1 SDI/HDSDI output per screen; SMPTE 259M-C, 292M / ITU-R BT.601; female BNC
Tally
2 LEDs (Green, Red) per monitor; female HD-15 connector
Color temperature
D65 (6500° Kelvin)
Color Gamut
SMPTE-C/EBU
Luma Linearity
Typical +/- 3% with 5 ire increments (0 to 10 ire)
Power Required
10.4 to 16.8 VDC
Power Consumption
36 watt nominal for V-R1042DP-TE
Operating Temperature
32°F to 120°F (0°C to 50°C)
Storage Temperature
-4°F to 120°F (-20°C to 50°C)
Compliance
₠, FCC-Class A, ANSI-63.4 (Certificates on file)
RoHS WEEE/Environmental
Do not dispose. Return to Manufacturer or Authorized Recycle Facility
V-PS12-5V-1 Power Supply
14-10 VDC (Universal Voltage 5.0Amps max - UL Class 2 supply included)
6
Mechanical Specification
V-R1042DP-TE4U
V-PS12-5V-1 Power Supply
Dimensions (W x H x D)
(Main body only)
18.9” x 7.0” x 1.6”
4.13” x 2.50” x 1.25”
Approx. Weight
5.0 lbs
0.65 lbs
7
Faceplate Cleaning
Faceplate Cleaning
When cleaning the faceplate it is very important to use non-abrasive and ammonia free cleaning agents and a clean micro fiber
cloth.
Do not use paper towels. Paper towel fibers are coarse and may scratch the surface of the Polycarbonate faceplate.
Paper towels may also leave streaks on the surface. Antistatic and fingerprint resistant cleaning agents are recommended.
Wash protective cover with a solution of mild soap or detergent and lukewarm water. Use a clean soft cloth, applying only light pres-
sure. Rinse with clean water and dry by blotting with a damp cloth or chamois. Grease, oil or tar may be removed with a good grade
of hexane, aliphatic naphtha, or kerosene. These solvents may be obtained at a paint or hardware store and should be used in ac-
cordance with manufacturer’s recommendations.
DO NOT USE: window cleaning sprays, kitchen scouring compounds or solvents such as acetone, gasoline, benzene,
alcohol, carbon tetrachloride, or lacquer thinner. These can scratch the sheet’s surface and/or weaken the sheet causing
small surface cracks called “crazing.”
Faceplate Dusting
Dust with a soft, damp cloth or chamois. Dry or gritty cloths may cause surface scratches and create a static electric charge on the
surface. Neutralizing static electricity effects by using recommended cleaning and polishing practice.
Faceplate Polishing
Protect and maintain surface gloss by occasional polishing with a good plastic cleaner and polish. Apply a thin, even coat with a soft
clean cloth and polish lightly with cotton flannel. Then wipe with a damp cloth to help eliminate electrostatic charges that can attract
dust particles.
Marking on the Faceplate
Use SHARPEE or equivalent marker. Clean as per instructions with an ammonia free cleaning agent.
V-R1042DP-TE4U User’s Guide