JVC DR-MH20S 사용자 설명서
Masterpage:Right0
EN
19
Filename [DR-MH30US_04Name.fm]
Page 19
Thursday, 8 July 2004 15:30
INSTALLING YOUR NEW UNIT
It’s essential that your unit be properly connected.
1
Make sure the package contains all of the accessories listed in
“SPECIFICATIONS” on page 78.
2
Place the unit on a stable, horizontal surface.
3
Connect the unit to a TV depending on the TV and cables you
use.
8 AV Connection
To connect to a TV with AV input connectors —
A Disconnect the TV aerial cable from the TV.
B Connect the TV antenna cable to the ANTENNA IN connector
8 AV Connection
To connect to a TV with AV input connectors —
A Disconnect the TV aerial cable from the TV.
B Connect the TV antenna cable to the ANTENNA IN connector
on the rear panel of the unit.
C Connect the provided RF cable between the ANTENNA OUT
connector on the rear panel of the unit and the TV’s antenna
terminal.
terminal.
D Connect the provided audio/video cable between the AUDIO/
VIDEO OUTPUT connectors on the rear panel of the unit and
the TV’s audio/video input connectors.
the TV’s audio/video input connectors.
8 S-Video Connection
To connect to TV’s S-VIDEO input and AUDIO input
connectors —
A Perform A – C in “AV Connection”.
B Connect the unit’s S-VIDEO OUTPUT connector to the TV’s
To connect to TV’s S-VIDEO input and AUDIO input
connectors —
A Perform A – C in “AV Connection”.
B Connect the unit’s S-VIDEO OUTPUT connector to the TV’s
S-VIDEO input connector.
C Connect the unit’s AUDIO OUTPUT connectors to the TV’s
AUDIO input connectors.
● You can obtain high-quality S-VHS pictures.
● If your TV is not stereo-capable, use the unit’s AUDIO OUTPUT
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
reproduction.
8 Component Video Connection
To connect to TV’s component video input connectors —
A Perform A – C in “AV Connection”.
B Connect the unit’s COMPONENT OUTPUT connectors to the
To connect to TV’s component video input connectors —
A Perform A – C in “AV Connection”.
B Connect the unit’s COMPONENT OUTPUT connectors to the
TV’s component video input connectors.
C Connect the unit’s AUDIO OUTPUT connectors to the TV’s
AUDIO input connectors.
● You can obtain high-quality component video pictures.
● If your TV is not stereo-capable, use the unit’s AUDIO OUTPUT
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
reproduction.
● By using the component video connection, you can view the images
in the progressive mode. For switching to the progressive mode, refer
to “Scan Mode Set” (
to “Scan Mode Set” (
4
Plug the end of the AC power cord into an AC outlet. This unit
performs Plug & Play Set automatically. (
● “LOADING” blinks on the front display panel when the AC plug of the
AC power cord is connected into an AC outlet and it takes
approximately 50 seconds for the unit to be turned on. This is not a
malfunction.
approximately 50 seconds for the unit to be turned on. This is not a
malfunction.
Basic Connections
L-1
1
Antenna or Cable
Matching transformer
(not provided)
(not provided)
Coaxial cable
AC outlet
Back of unit
Component
video cable
(not provided)
Flat feeder
TV
AC power cord
To 75 ohm
terminal
Audio/video cable
(provided)
(provided)
S-Video cable
(not provided)
(not provided)
COMPONENT OUTPUT
AUDIO/VIDEO
OUTPUT
OUTPUT
ANTENNA IN
ANTENNA
OUT
RF cable
(provided)
(provided)
S-VIDEO OUTPUT
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
OPERATION CAN BE PERFORMED.
DR-MH30US_00.book Page 19 Thursday, July 8, 2004 3:32 PM