JVC DR-MV5SEK 사용자 설명서

Masterpage:Right+

Filename [MV5SEK_08Basic TimerDub.fm]

Page 31Wednesday, 31 August 2005  19:58

You can programme each deck to timer-record as many as 
8 programmes up to 30 days ahead.
If you do not know the PlusCode number for the programme you 
wish to record, use the following procedure to set your unit to 
timer-record the programme.

● When two successive programmes are recorded on a DVD-RW disc 

with Manual Timer Programming function, the beginning of the 
second one may be left off the recording.

● If the copy limited programme is received during timer-recording, the 

unit enters Record Pause mode. Recording starts again if it is 
switched to a recordable broadcast during the time you programmed.

● In case of a power failure after programming, the unit’s memory 

backup keeps your selections for approximately 10 minutes.

● Programmes that start after midnight must have the next day’s date.

● To record the programmes received by the satellite receiver, record 

on the DVD discs. For details, refer to “Satellite Receiver Users (DVD 
Deck Only)” above.

Press DVD or VHS to select the deck on which you want to 

perform timer programming.

Load a recordable disc.

For VHS deck
Load a cassette with safety tab intact.

Press PROG to access the 

Programme Check screen.

Press rt w e to select “DVD” 
and press rt to select “NEW 
TIMER PROGRAMME”, then 
press ENTER.

For VHS deck
Press rt w e to select “VHS” 
and press rt to select “NEW 
TIMER PROGRAMME”, then 
press ENTER.

Press rt to set the desired 

date.

● The current date appears on the 

TV screen. The date you enter 
appears in its place.

Press w e to select “START”, then press rt to set the desired 

start time.

● Each press of rt advances/goes back the start time in 1-min. 

increments.

● To advance/go back the start time in 30-min. increments, press and 

hold rt.

Press w e to select “STOP”, then press rt to set the desired 

stop time.

● Each press of rt advances/goes back the stop time in 1-min. 

increments.

● To advance/go back the stop time in 30-min. increments, press and 

hold rt.

Press w e to select “TV PROG”, then press rt to select the 

desired channel.

Press w e to select the desired recording option as required.

● Refer to step 6 in “VIDEO Plus+ Timer Programming” (

pg. 29).

Press ENTER to access the Programme Confirmation screen.

Press ENTER to complete timer programming.

● To programme another timer, repeat steps 3 – 11.

● If “PROGRAMME OVERLAPPED” appears on the TV screen, see 

page 35.

Press TIMER # to engage the unit’s timer mode. The DVD 

timer indicator lights up on the unit and the unit is automatically 
turned off.

● To disengage the timer mode, press TIMER # again.

● Make sure that the unit’s built-in clock is set properly.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/DVD switch to DVD.

Satellite Receiver Users (DVD Deck Only)
To timer-record a satellite broadcast using Manual Timer 
Programming:
A Perform “Manual Timer Programming”.
B Set the satellite receiver to the appropriate channel before 
the selected programme begins.
C Select “L-2” in step 8.
D Leave the satellite receiver’s power on.

rtwe

VHS

DVD

19:00 - 20:00
22:00 - 22:30
13:30 - 14:00
16:00 - 17:00

PROG

++++++++++++++++ NEW TIMER PROGRAMME ++++++++++++++++

DISC TIMER PRGM

SELECT WITH [CURSORS]
THEN PRESS [ENTER]

OK

SELECT

EXIT

05/07 SAT

44

SP

10/07 THU

10

XP

11/07 FRI

26

LP

WEEKLY

11/07 FRI

33

LP

DATE

START-STOP

TV PROG

VPS/PDC REC MODE

DAILY/WEEKLY

ON

OFF
OFF

ON

LP

VTM 10

20:30

20:00

TIMER PROGRAMME

DATE

START

STOP

TV PROG

05/07 SAT

DAILY/WEEKLY

VPS/PDC

OFF

NAME

SET TIMER PROGRAMMING WITH [CURSORS]
THEN PRESS [ENTER]

REC MODE

CONFIRM

SELECT

PROG

EXIT

MV5SEK_00.book  Page 31  Wednesday, August 31, 2005  7:58 PM