AT&T 945 사용자 설명서
Parts List
Your box should include:
Tools Needed
You will also need a small Phillips head screw driver to install your phone.
2
BEFORE YOU BEGIN
BEFORE Y
OU
BEGIN
BEFORE Y
OU
BEGIN
Please also read
Part 1 — Important
Product Information
USER’S MANUAL
Part 2
© 2004 Advanced American Telephones. All Rights Reserved.
AT&T and the Globe Design are trademarks of AT&T Corp., licensed to Advanced American Telephones.
Four-Line Intercom
Speakerphone 945
Coiled
handset cord
handset cord
Power adapter
Eight-inch line cord
Two seven-foot line cords
Handset
This User’s
Manual
Manual
Base Unit
This Quick Start Guide provides basic instructions.
For addtional installation options and complete
instructions which allow you to use all features
of this phone, refer to your User's Manual.
For addtional installation options and complete
instructions which allow you to use all features
of this phone, refer to your User's Manual.
INSTALLATION
Installation of a DSL splitter and an AT&T Z800A filter
is required to use the advanced features of this
telephone if you have DSL (Digital Subscriber Line)
service. Please see “DSL Users” starting on page 4 of
your User’s Manual for details.
is required to use the advanced features of this
telephone if you have DSL (Digital Subscriber Line)
service. Please see “DSL Users” starting on page 4 of
your User’s Manual for details.
If you are installing multiple phones in your phone
system, you must install and program one set at a time.
Each phone must be assigned a unique extension
number.
system, you must install and program one set at a time.
Each phone must be assigned a unique extension
number.
Battery Installation
Install a 9V alkaline battery (purchased separately) in order to
use some features of this telephone in the event of a power
failure.
use some features of this telephone in the event of a power
failure.
1
Remove the wedge from the underside of the
base unit. Press on the tabs and pull the wedge away
from the phone.
base unit. Press on the tabs and pull the wedge away
from the phone.
2
Remove the battery compartment screw with
a small Phillips head screwdriver.
a small Phillips head screwdriver.
3
Pull on the tab to remove the battery
compartment cover.
compartment cover.
4
Insert a 9V battery (purchased separately)
following the polarity diagram inside the battery
compartment.
following the polarity diagram inside the battery
compartment.
5
Replace the battery compartment cover and
the screw.
the screw.
6
Reattach the wedge to the base unit by sliding the
tabs into the holes. Snap the wedge onto the base.
tabs into the holes. Snap the wedge onto the base.
Table/Desk Installation
For best results, follow the directions in “Battery Installation”
above, before installing the phone.
above, before installing the phone.
1
Connect the telephone line cords to the
telephone as shown in the appropriate
illustration below.
telephone as shown in the appropriate
illustration below.
•
Four One-Line Jacks (To use this installation
option, you’ll need to purchase two two-line
adapters. Adapters are available at retail stores or
by calling
option, you’ll need to purchase two two-line
adapters. Adapters are available at retail stores or
by calling
1 800 222–3111.)
•
Two Two-Line Jacks
2
Connect the handset cord.
Plug one end of the coiled handset cord into the jack
on the left side of the phone. Plug the other end into
the handset and hang up.
on the left side of the phone. Plug the other end into
the handset and hang up.
QUICK START GUIDE
Four-Line Intercom
Speakerphone 945
Speakerphone 945
Two-line adapters
Telephone line cords
Modular
telephone jacks
Lines 3 and 4
telephone jacks
Lines 3 and 4
Modular
telephone jacks
Lines 1 and 2
telephone jacks
Lines 1 and 2
L1/L2 jack
L3/L4 jack
Modular
telephone jack
Lines 3 and 4
Modular telephone
jack Lines 1 and 2
jack Lines 1 and 2
Telephone
line cords
L1/L2 jack
L3/L4 jack