Panasonic DW10000U 사용자 설명서
62
– ENGLISH
Note
The abovementioned vertical stripes will not appear
on the screen when all signals are input.
on the screen when all signals are input.
The picture may be distorted during the adjusting
operation, but this is not a fault.
operation, but this is not a fault.
The input resolution can be adjusted only when
RGB signal input is applied with RGB1 and RGB2
IN.
RGB signal input is applied with RGB1 and RGB2
IN.
Adjusting the clamp
position
position
Use the clamp position adjustment to achieve the
optimal value when dark areas of the image are
crushed or displayed in green.
optimal value when dark areas of the image are
crushed or displayed in green.
1. Press
▲▼ to select “CLAMP
POSITION”.
2. Press ENTER.
The “CLAMP POSITION” screen will be
displayed.
displayed.
3. Press
◄► to adjust.
The value changes from 1 to 255.
The optimal value for the clamp position
adjustment
If dark areas are crushed:
The optimal value is the point where the dark
area is best improved.
If the dark areas are displayed in green:
The optimal value is the point where the green
area becomes dark and clear.
adjustment
If dark areas are crushed:
The optimal value is the point where the dark
area is best improved.
If the dark areas are displayed in green:
The optimal value is the point where the green
area becomes dark and clear.
Note
The clamp position can be adjusted only when the
RGB signal input is applied with RGB1 and RGB2
IN.
RGB signal input is applied with RGB1 and RGB2
IN.
•
•
•
•
•
•
•
ADVANCED MENU
DIGITAL CINEMA REALITY
BLANKING
INPUT RESOLUTION
BLANKING
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING
FRAME DELAY
RASTER POSITION
FRAME DELAY
RASTER POSITION
MENU SELECT
SUB MENU
AUTO
OFF
DEFAULT
ENTER
ADVANCED MENU
DIGITAL CINEMA REALITY
BLANKING
INPUT RESOLUTION
BLANKING
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING
FRAME DELAY
RASTER POSITION
FRAME DELAY
RASTER POSITION
MENU SELECT
SUB MENU
AUTO
OFF
DEFAULT
ENTER
CLAMP POSITION
POSITION
POSITION
MENU SELECT
ADJUST
1
CLAMP POSITION
POSITION
POSITION
MENU SELECT
ADJUST
1
Edge blending adjustment
This projector has the function to hide the seams for
multi-screens.
multi-screens.
1. Press
▲▼ to select “EDGE
BLENDING”.
2. Press
◄► to switch “EDGE
BLENDING”.
The setting will change as follows each time
◄► is pressed.
◄► is pressed.
OFF:
When the multi-screens are not going to be
used.
When the multi-screens are not going to be
used.
ON:
When the tilting inside the unit is to be used for
the tilting of the edge blending area.
When the tilting inside the unit is to be used for
the tilting of the edge blending area.
USER:
When a specific tilting is to be used for the
tilting of the edge blending area. (Separate
software is required to establish these settings.
Consult your dealer.)
When a specific tilting is to be used for the
tilting of the edge blending area. (Separate
software is required to establish these settings.
Consult your dealer.)
3. Press ENTER.
The “EDGE BLENDING” screen will be
displayed.
displayed.
•
•
•
•
•
ADVANCED MENU
DIGITAL CINEMA REALITY
BLANKING
INPUT RESOLUTION
CLAMP POSITION
BLANKING
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING
FRAME DELAY
RASTER POSITION
RASTER POSITION
MENU SELECT
CHANGE
AUTO
OFF
DEFAULT
ADVANCED MENU
DIGITAL CINEMA REALITY
BLANKING
INPUT RESOLUTION
CLAMP POSITION
BLANKING
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING
FRAME DELAY
RASTER POSITION
RASTER POSITION
MENU SELECT
CHANGE
AUTO
OFF
DEFAULT
OFF
ON
USER
OFF
ON
USER
ENTER
EDGE BLENDING
UPPER START
UPPER START
OFF WIDTH
LOWER START
OFF WIDTH
LEFT START
OFF WIDTH
RIGHT START
OFF WIDTH
MARKER
BRIGHT ADJUST
LOWER START
OFF WIDTH
LEFT START
OFF WIDTH
RIGHT START
OFF WIDTH
MARKER
BRIGHT ADJUST
MENU SELECT
ADJUST CHANGE
0
128
0
128
0
128
0
128
OFF
OFF
ENTER
EDGE BLENDING
UPPER START
UPPER START
OFF WIDTH
LOWER START
OFF WIDTH
LEFT START
OFF WIDTH
RIGHT START
OFF WIDTH
MARKER
BRIGHT ADJUST
LOWER START
OFF WIDTH
LEFT START
OFF WIDTH
RIGHT START
OFF WIDTH
MARKER
BRIGHT ADJUST
MENU SELECT
ADJUST CHANGE
0
128
0
128
0
128
0
128
OFF
OFF
How to use ADVANCED MENU (continued)