Samsung HL-T5656W 사용자 설명서
English - 22
Setting Up Your Remote Control
After your remote control has been properly set up, your remote control can operate in five different modes: TV, VCR, Cable,
DVD, or Set-Top Box. Pressing the corresponding button on the remote control allows you to switch among these modes,
and control whichever piece of equipment you choose.
➢
The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top Boxes.
Setting Up the Remote to Operate Your VCR
1 Turn off your VCR.
2 Press the VCR button on your TV’s remote control.
3 Press the SET button on your TV’s remote control.
4 Using the number buttons on your remote control, enter three digits of the VCR code listed
on page 24 of this manual for your brand of VCR. Make sure you enter three digits of the
code, even if the first digit is a “0”. (If more than one code is listed, try the first one.)
5 Press the POWER button on the remote control. Your VCR should turn on if your remote is
set up correctly.
If your VCR does not turn on after set-up, repeat steps 2, 3 and 4, but try one of the other
codes listed for your brand of VCR. If no other codes are listed, try each VCR code, 000
through 080.
Note on Using Remote Control Modes: VCR
When your remote control is in
VCR mode, the volume buttons still control your TV’s volume.
Continued...
Storing Channels in Memory (Automatic Method)
3 Press the ▲ or ▼ button to select Auto Program, then press the ENTER button.
4 Press the ◄ or ► button to select an antenna connection, then press the ENTER button.
4 Press the ◄ or ► button to select an antenna connection, then press the ENTER button.
➢
Air: “Air” antenna signal.
Cable: “Cable” antenna signal.
Air+Cable: “Air” and “Cable” antenna signals.
➢
If the antenna is connected to ANT 1 IN (CABLE), select
Cable and if it is connected to
ANT 2 IN (AIR), select
Air.
➢
If both ANT 1 IN (CABLE) and ANT 2 IN (AIR) are connected, select the
Air+Cable.
➢
If you selected
Air, then go to step 6.
5 Press the ◄ or ► to select the correct analog signal source among STD, HRC, and IRC,
then press the
ENTER button. If you have Digital cable, select the signal source for both
Analog and Digital.
➢
STD, HRC, and IRC identify various types of cable TV systems.
Contact your local cable company to identify the type of cable system that exists in
your particular area. At this point the signal source has been selected.
6 The TV begins memorizing all available stations.
When pressing the
ENTER button during a storing process, the message Would you like
to stop the auto channel selection? is displayed. Select Yes by pressing the ◄ or ►
button.
Press the
Press the
EXIT button to exit.
➢
The TV must be connected to an antenna/cable in order to receive digital TV signals.
Even if a particular channel is deleted from the memory, you can always tune to that
channel directly by using the number buttons on the remote control.
➢
All available DTV and analog channels are automatically stored in memory.
It takes approximately 3 to 10 minutes to memorize channels.
Auto Program
Select the antennas to memorize
Air
Cable
Air+Cable
Enter
Return
Auto Program
Auto Program in Progress.
Cable 3
10%
Stop
Enter
Return
Auto Program
Selects the cable system.
Analog
Digital
STD
HRC
IRC
STD
HRC
IRC
Enter
Return
Auto Program
Would you like to stop the auto channel
selection?
Cable 3
10%
Yes
No
Enter
Return
BN68-00630E-Eng_1.indd 22
2007-04-09 ｿﾀﾈﾄ 5:56:28