사용자 설명서차례Contents5Hardware Configuration111.1 Introduction121.2 Specifications131.2.1 Standard SBC functions131.2.2 VGA interface141.2.3 Ultra 2 SCSI Interface (MIC-3365 and MIC-3365F)141.2.4 Mechanical and environmental specifications141.3 Safety Precautions151.4 Function Block Diagram161.5 Board Dimensions171.6 Jumpers181.6.1 Jumper Locations181.6.2 Jumper Settings191.6.3 Clear CMOS (JP5)201.7 Connectors211.8 Front Panel Connectors and Indicators231.9 Installing SDRAM (DIMMs)241.10 Installing CPU heat sink and HDD, FDD brackets261.11 Software Support28CHapter 2 Connecting Peripherals292.1 IDE Device (CN12)302.2 Floppy Drive (CN11)302.3 VGA Display Connector (CN2)312.4 Parallel Port Connector (CN1)312.6 Serial Ports (CN13 and CN6)312.7 Ethernet Configuration (CN4 and CN5)322.8 USB Connector (CN8)322.9 Ultra 2 SCSI Interface332.10 Card Installation33Chapter 3 Ethernet Software Configuration353.1 Introduction363.2 Utility and Drivers363.3 Installation for Windows NT 4.039Chapter 4 AGP VGA Setup494.1 Introduction504.2 Installation of SVGA Driver504.3 Installation for Windows NT 4.051Chapter 5 SCSI Software Configuration575.1 Introduction585.2 Utility and Drivers585.3 Installation for Windows NT 4.060Chapter 6 Award BIOS Setup696.1 Introduction706.2 Entering Setup706.3 Standard CMOS Features716.4 Advanced BIOS Features726.5 CHIPSET Features Setup756.6 Integrated Peripherals756.7 Power Management Setup766.8 PnP/PCI Configurations776.9 Load Optimized Defaults786.10 Set Password796.11 Save & Exit Setup806.12 Exit Without Saving81Appendix A Programming the Watchdog Timer83A.1 Programming the Watchdog Timer84Pin Assignments87B.1 VGA Display Connector (CN2)88B.2 Keyboard and Mouse Connnector (CN7)88B.3 COM1 and COM2 Serial Port (CN13 and CN6)89B.4 USB Connector (CN8)90B.5 Ethernet RJ-45 Connector (CN4 and CN5)90B.6 Parallel Port Connector (CN1)91B.7 IDE Connector (CN12)92B.8 Floppy Drive Connnector (CN11)93B.9 System I/O Ports94B.10 DMA Channel Assignments95B.11 Interrupt Assignments95B.12 1st MB Memory Map96B.13 J1 connector pin assignments97B.14 J2 connector pin assignments98B.15 J3 connector pin assignments99B.16 J4 connector pin assignments100B.17 J5 connector pin assignments101Tables8Table 1-1: MIC-3365 jumper descriptions18Table 1-2: Clear CMOS20Table 1-3: MIC-3365 connector descriptions21Table 1-4: Recommended SDRAM25Table 2-1: MIC-3365 serial port default settings32Table B-1: MIC-3365 CRT display connector88Table B-2: MIC-3365 keyboard connector88Table B-3: MIC-3365 COM1 and COM2 serial port89Table B-4: MIC-3365 USB1/USB2 connector90Table B-5: MIC-3365 Ethernet RJ-45 connector90Table B-6: MIC-3365 parallel port connector91Table B-7: MIC-3365 IDE connector92Table B-8: MIC-3351 floppy drive connector93Table B-9: System I/O ports94Table B-10: DMA channel assignments95Table B-11: Interrupt assignments95Table B-12: 1st MB memory map96Table B-13: J1 connector pin assignments97Table B-14: J2 connector pin assignments98Table B-15: J3 connector pin assignments99Table B-16: J4 connector pin assignments100Table B-17: J5 connector pin assignments101Figures9Figure 1-1: MIC-3365 function block diagram16Figure 1-2: MIC-3365 board dimensions17Figure 1-3: MIC-3365 jumper locations18Figure 1-4: MIC-3365 connector locations22Figure 1-5: MIC-3365 front panel connector and indicator locations23Figure 1-6: Heat sink installation for 1 slot wide solution26Figure 1-7: Heat sink installation for 2 slot wide solution27Figure 2-1: Installing the card into the chassis34Figure 6-1: Initial Setup screen70Figure 6-2: Standard CMOS Features screen71Figure 6-3: Advanced BIOS Features screen72Figure 6-4: Advanced Chipset Features screen75Figure 6-5: Integrated Peripherals screen76Figure 6-6: Power Management Setup screen77Figure 6-7: PnP/PCI Configurations screen78Figure 6-8: Load Optimized Defaults screen78Figure 6-9: Set Password screen79Figure 6-10: Save & Exit Setup screen80Figure 6-11: Exit Without Saving screen81크기: 1.15메가바이트페이지: 102Language: English매뉴얼 열기