사용자 설명서차례SAFETY INFORMATION3Federal Communications Commission Regulations3Compliance with RF Exposure Standards3RF Exposure Compliance and Control Guidelines and Operating Instructions3Mobile Antennas4Approved Accessories4Contact Information4TABLE OF CONTENTS5SECTION 1 GENERAL81.1 Features81.2 General Features81.2.1 Conventional Features81.2.2 SMARTNET/SmartZone Features81.2.3 Project 25 Trunked Features9SECTION 2 CONTROLS AND DISPLAY102.1 Front Panel Controls102.2 Rear Panel Connectors112.3 Display11SECTION 3 GENERAL OPERATION133.1 Turning Power On and Setting Volume133.1.1 Power ON/OFF133.1.2 Setting Volume Level133.2 Power-Up Password133.2.1 General133.2.2 Password Features With Later Models133.2.3 Password Features with Early Unrevised Models133.3 Backlight Control and Display Viewing Angle Adjust143.4 Zone/Channel Display and Select143.4.1 Zone/Channel Display143.4.2 Zone/Channel Select143.4.3 Direct Channel Select143.5 Setting Squelch Control153.6 Transmit Disable153.7 Radio Operating Modes153.7.1 General153.7.2 Conventional Mode163.7.3 SMARTNET/SmartZone Mode163.7.4 P25 Trunked Mode163.7.5 Systems, Channels, and Zones17SECTION 4 RADIOWIDE FEATURES184.1 Option Switches194.2 Time-Out Timer194.3 Home Zone/Channel Select194.4 Power Output Select194.5 Alert Tone Select194.6 Power Turn-Off Delay194.7 Horn Alert204.8 Microphone Off-Hook Detect204.9 Surveillance Mode204.10 Public Address204.11 Scanning214.11.1 Introduction214.11.2 Standard Scanning214.11.3 Radio Wide Scanning214.11.4 Scan Hold Time224.11.5 Transmitting in the Scan Mode224.11.6 Nuisance Channel Delete224.12 Scan Lists224.12.1 Standard Mode Scan Lists224.12.2 Radio Wide Scan List24SECTION 5 CONVENTIONAL FEATURES255.1 Introduction255.2 Monitoring Before Transmitting255.3 Monitor Mode255.4 Busy Channel Lockout265.5 Call Guard Squelch265.5.1 Introduction265.5.2 Call Guard Squelch Enable/ Disable265.5.3 Tone Call Guard Squelch265.5.4 Digital Call Guard Squelch265.5.5 Selective Squelch Code Select (CTCSS/DSC/NAC)275.6 Penalty Timer275.7 Conversation Timer275.8 Repeater Talk-Around285.9 Displaying Transmit/Receive Frequency285.10 Emergency Alarm and Call285.10.1 Introduction285.10.2 Emergency Alarms285.10.3 Emergency Calls295.11 Conventional Mode Scanning295.11.1 General295.11.2 Selecting a Scan List295.11.3 Transmitting in Scan Mode295.11.4 Priority Channel Sampling305.12 Standard Conventional Calls315.13 DTMF/ANI Signaling315.14 Single Tone Encoder325.15 Project 25 Mode Features325.15.1 Unit ID Code325.15.2 Group ID Code325.15.3 Network Access Code (NAC)325.15.4 P25 Group Calls325.15.5 P25 Unit Calls325.15.6 Call Alert335.15.7 Messaging345.15.8 Status Messaging345.15.9 P25 Packet Data345.16 Keypad Programming345.16.1 Introduction345.16.2 Menu Structure355.16.3 Zone Password355.16.4 Zone Change Parameter355.16.5 Channel Change Parameter355.16.6 System Parameters355.16.7 Channel Parameters36SECTION 6 SMARTNET/SMARTZONE/P25 TRUNKED FEATURES386.1 Introduction386.2 Analog and Digital Operation386.3 Viewing Unit ID386.4 Standard Group Calls386.4.1 Introduction386.4.2 Placing a Standard Group Call386.4.3 Receiving a Standard Group Call386.5 Private (Unit-To-Unit) Calls396.5.1 General396.5.2 Placing an Enhanced Private Conversation Call396.5.3 Placing a Standard Private Conversation Call406.5.4 Receiving a Private Call (All Types)406.6 Telephone Calls406.6.1 General406.6.2 Placing a Telephone Call416.6.3 Receiving a Telephone Call416.7 Call Alert416.8 Messaging426.9 Sending Status Conditions426.10 Emergency Alarm and Call436.10.1 Introduction436.10.2 Emergency Alarms436.10.3 Emergency Calls436.11 Failsoft Operation446.12 SMARTNET/SmartZone/P25 Trunked Scanning Features446.12.1 General446.12.2 Priority Talk Group Sampling456.12.3 Scan List Editing and Selection456.13 Dynamic Regrouping456.14 SmartZone and P25 Trunking Unique Features456.14.1 Introduction456.14.2 Busy Override466.14.3 Site Trunking466.14.4 Determining Current Site and Searching For a New Site466.14.5 Locking/Unlocking a Site466.14.6 ZoneFail Site Lock46SECTION 7 MISCELLANEOUS477.1 Supervisory Tones477.2 System Operator Programming477.3 Speaking Into Microphone487.4 Operation At Extended Range487.5 Preventing Battery Discharge487.6 Licensing487.7 Radio Service48SECTION 8 DETERMINING AVAILABLE OPTIONS498.1 General498.2 Upgrading A Radio With New Options498.3 Using PCConfigure To Determine Options49SECTION 9 5300 MOBILE FIRMWARE VERSIONS519.1 General519.2 Early Unrevised Logic Board519.3 Programming Software Required519.4 Firmware Required519.5 Identifying Radios With Revised Logic Board51SECTION 10 PASSWORD DESCRIPTION5210.1 New Password Enhancements5210.1.1 Introduction5210.1.2 Software Versions Required5210.1.3 Availability With Earlier Versions5210.2 Programming Passwords5210.2.1 General5210.2.2 Lost Passwords5210.2.3 Changing Passwords5310.2.4 Password Entry Procedure5310.3 Password Description5310.3.1 User (Power-On) Passwords5310.3.2 Download/Upload Passwords5310.3.3 Master Password5310.4 Zone Password53SECTION 11 SECURE COMMUNICATION (ENCRYPTION)5411.1 General5411.1.1 Introduction5411.1.2 Encryption Algorithms5411.1.3 Encryption Available With Various Channel Types5411.1.4 5300 Encryption Capabilities5411.1.5 FIPS and Non-FIPS Modes5511.2 Encryption Keys5511.2.1 Introduction5511.2.2 Key and Algorithm IDs5511.2.3 PID/SLN Key Management Modes5511.2.4 Maintaining Keys in Memory5611.2.5 Encryption Key Select5611.2.6 Encryption Key Erase5611.3 Clear/Secure Strapping5611.3.1 Transmit Mode Options5611.3.2 Receive Mode Options5711.3.3 Talk Group Encryption override5711.3.4 Encryption Icon Operation5711.4 OTAR (Over-The-Air Rekeying)5811.4.1 Introduction5811.4.2 Encryption Key Types5811.4.3 Keysets5811.4.4 Crypto Groups5811.4.5 Key Management Facility5911.4.6 Message Number Period (MNP)5911.4.7 Definitions5911.5 Radio Setup For Encryption6111.5.1 General Encryption Setup6111.5.2 Additional Setup For OTAR6211.6 Radio OTAR Capabilities6311.6.1 SEM 5100/5300, Standard 51006311.6.2 UCM Equipped 53006311.6.3 OTAR Option Switches63INDEX65크기: 1.48메가바이트페이지: 67Language: English매뉴얼 열기