STMicroelectronics STLDC08 Demo Board STEVAL-ILL039V1/2 STEVAL-ILL039V1 사용자 매뉴얼

차례

• Table 1. Device summary

  1
• 1 Application diagram

  4
  • Figure 1. Electric schematic optimized for 2 LEDs and ILED = 200 mA

    4
  • Table 2. List of components

    4
  • Figure 2. Electric schematic optimized for 4 LEDs and ILED = 300 mA

    5
  • Table 3. List of components

    5
• 2 Absolute maximum ratings

  6
  • Table 4. Absolute maximum ratings

    6
  • Table 5. Thermal data

    6
• 3 Pin configuration

  7
  • Figure 3. Pin connections (top through view)

    7
  • Table 6. Pin description

    7
• 4 Electrical characteristics

  8
  • Table 7. Electrical characteristics

    8
• 5 Typical performance characteristics

  10
  • Figure 4. VFB vs. temperature

    10
  • Figure 5. Maximum VSENSE vs. temperature

    10
  • Figure 6. IOUT vs. temperature FB = 0.5 V

    10
  • Figure 7. IOUT vs. temperature FB = GND

    10
  • Figure 8. Efficiency vs. input voltage 2 LEDs

    10
  • Figure 9. Efficiency vs. input voltage 4 LEDs

    10
  • Figure 10. Startup timing and dimming ILED vs. time, 2 LEDs

    11
  • Figure 11. Dimming EN/PWM = 200 Hz, 2 LEDs

    11
  • Figure 12. Startup timing and dimming ILED vs. time, 4 LEDs

    11
  • Figure 13. Dimming EN/PWM = 200 Hz, 4 LEDs

    11
  • Figure 14. VCC = 1.5 V; ILED = 200 mA, 2LEDs

    11
  • Figure 15. VCC = 3.6 V; ILED = 300 mA, 4LEDs

    11
• 6 Block diagram

  12
  • Figure 16. Block diagram

    12
• 7 Detailed description

  13
  • 7.1 Main control loop

    13
  • 7.2 Start up

    13
    • Figure 17. Timing diagram

      14
  • 7.3 Over voltage protection (OVP)

    14
  • 7.4 Enable/PWM

    14
  • 7.5 Dimming

    15
• 8 Application information

  16
  • 8.1 LED current programming

    16
  • 8.2 Duty cycle

    16
  • 8.3 Inductor selection

    16
    • Figure 18. Timing diagram

      17
  • 8.4 Inductor peak current limit

    18
  • 8.5 Power MOSFET selection

    19
    • Figure 19. Current diagram ON state

      20
    • Figure 20. Current diagram OFF state

      20
  • 8.6 Schottky diode selection

    21
  • 8.7 Input capacitor

    21
  • 8.8 Output capacitor

    21
• 9 Demonstration board

  22
  • Figure 21. Electrical schematic

    22
  • Table 8. Bill of material optimized for 2 LEDs and ILED = 200 mA

    22
• 10 Layout suggestion

  23
  • Figure 22. Assembly layer

    23
  • Figure 23. Top layer

    23
  • Figure 24. Bottom layer

    24
• 11 Package mechanical data

  25
• 12 Revision history

  28
  • Table 9. Document revision history

    28