Accusplit 998-310 Folheto

1. Turn the watch over and select the correct size Phillips

screwdriver (the fastening is very tight, so the screws

will strip easily if you use the wrong size or type of

screwdriver).

2. Remove all six screws from the back of the case, and

set aside so they will not get lost.

3. Gently pry the watch back

away from the case front,

using the gap near the

middle button. The electronics

module will come away with

the case back. You will have

to slide the back downwards

to free the electronics module

from the button actuator bars.

The lanyard will also come loose - set it aside.

4. Hold the case back with

electronics module face up

in one hand. Use your other

hand to gently pull the

electronics module loose

from the case back. The

green circuit board will

come away with the module.

Try to leave the gray rubber

gasket in place (see step 7).

5. Turn the electronics module over to see the battery.

Use a small flat head screwdriver to gently push

the silver battery hold-down tab out of the way (it

is held in place with spring tension). With the

battery hold-down tab out of the way, you can

shake or pry the old battery loose.

6. Install a new CR2032 battery with + terminal

facing up.

7. If the gray gasket came loose from the case back,

reinstall it now.

a. First, line up the black gasket holder on top of the

case back, with the beveled side facing up.

b. Orient the gasket correctly. The three dark gray

pads must be facing up (away from the case

back).

c. Finally, put the gasket on top of the gasket

holder, and gently push both into the case back

until they pop into place.

8. Turn the electronics module over so that the battery

is facing the inside of the case back. Gently push the

electronics module down into the gray rubber

gasket, until it seats. It will be firmly in position if

this is done correctly.

9. Slide the button set out of the front case (you’ll see

that the three buttons are joined together into one

assembly).

10. Turn the button actuator set so that the flat part of

the buttons are facing the outside of the case back.

Now, slide the button set into the top of the case

back & electronics module assembly, so that the

button actuator bars slide down into the slots

between the top of the gray rubber gasket and the

case back.

11. Now, pick up the case front, holding it so that the

outside (front of the watch) is touching your palm.

Put the lanyard back into its slot in the bottom of

the case front.

12. Flip the electronics/case back assembly over and

gently press it back into the front case of the watch,

until it seats. The buttons should now work normally.

13. Replace and tighten the six screws in the case back.

Screws must be tight for the watch to be water

resistant again.

  1.  Plastic Lens
  2.  Name Plate
  3.  Case Front
  4.  (3) Button Set
  5.  Button Holder
  6.  Metal Clamp
  7.  LCD
  8.  LCD (Connector) (2)
  9.  LCD (Display Holder)
10.  PCB
11.  Battery Holder
12.  Gray Rubber Gasket
13.  Gasket Holder
14.  Case Back
15.  Negative Battery Contact
16.  Positive Battery Contact
17.  Warranty Label

601X3V

ACCUSPLIT®
A601X3V Stopwatch

Battery Changing Instructions

When the display on your watch begins to go dim, or if

it goes blank, the watch needs a new battery. The watch

uses a high capacity CR2032 Lithium battery, which has

an expected life of more than five years in this watch.
To change the battery, you will need a set of large jeweler’s

screwdrivers (including Phillips head).
Note: If this looks too complicated, you can always send

your watch back to ACCUSPLIT for battery changing instead.

See www.ACCUSPLIT.com/support for details.

9:49

ACCUSPLIT, Inc. • 3090 Independence Drive, Suite 148 • Livermore, CA 94551 USA

800-935-1996 • 925-290-1900 • FAX 925-290-1930 • www.ACCUSPLIT.com • support@ACCUSPLIT.com

998-310

Electronics module

Battery

Gray rubber

gasket

Battery hold-down tab