Xantech RC68+ Manual Do Utilizador
1
Amplifiers & Preamplifiers
RC68+
INSTALLATION INSTRUCTIONS
RC68+
PROGRAMMER / REMOTE CONTROL
The RC68+ programmer is a 55 key hand-held device that generates all the IR
codes necessary for the set up and operation of Xantech IR remote controlled
products. Such products include models ZPR68, RAT1, MIRV1, GATEKEEP-IR,
etc. The RC68+ is an upgrade of the previous 32 key RC68. While providing
additional key-code command capabilities, it retains all previous RC68 program-
ming in a similar 32 key layout section on the keypad.
codes necessary for the set up and operation of Xantech IR remote controlled
products. Such products include models ZPR68, RAT1, MIRV1, GATEKEEP-IR,
etc. The RC68+ is an upgrade of the previous 32 key RC68. While providing
additional key-code command capabilities, it retains all previous RC68 program-
ming in a similar 32 key layout section on the keypad.
GENERAL
• The RC68+ is used initially for the setup of system control parameters and IR
Code Groups for Xantech products.
• It is then used to "teach" a basic set of operational IR commands into universal
learning devices such as the Xantech URC series learning remotes, the
Xantech Smart Pads, the 590 Programmable Controller, the 710 Fone Link,
etc., for the end user.
Xantech Smart Pads, the 590 Programmable Controller, the 710 Fone Link,
etc., for the end user.
• Included with the RC68+ is a set of keypad overlays. These overlays are marked
with command names that apply to specific Xantech models. They are provided
to make it easier for the installer when setting up the system. See Fig. 2 and
the model listings below.
to make it easier for the installer when setting up the system. See Fig. 2 and
the model listings below.
• While the RC68+ will operate as a separate remote control, it is highly
recommended it not be given to the final user for the following reasons:
• Since it includes special setup codes, the user may inadvertently alter the
installer configurations.
• Also, since the user will require IR commands from other brands of equipment to control the total system,
in addition to those of the RC68+, all commands should be consolidated into one learning device, for ease
of use.
of use.
THE RC68+ OVERLAY SYSTEM
• The RC68+ base unit comes with a permanently attached keypad overlay (A) with lettering that identifies
the commands for operation of the model ZPR68 and other models with similar commands.
• Additional temporary overlays are included for use with
Xantech models that differ greatly from the ZPR68.
• The overlays are simply placed over the RC68+ keys, as
needed. Use the overlay that corresponds to the Xantech
model or models you are working with, as listed below.
model or models you are working with, as listed below.
Xantech Model
RC68+ Overlay Id Letter
RAT1, MIRV1, ............................................ A
(permanently attached
RGC11, RP41AV, to the RC68+)
RS41AV, ZPR68,
ZPR68-10
AC2, CC12, SR21 ...................................... B
RT8, RT16-10 ............................................ C
680-10, 686-10, CC62 ............................... D
Gatekeep-IR Modules ................................ E
IR-DC4 (RC68+ IR-to-RS232, Arrakis) ...... F
SmartPad
3
.................................................. I
A
60
88
A8
98
A
B
C
ADJ-OFF
1
2
3
4
5
6
7
8
GLOBAL
Z-ADJ
TREBLE
VOL
MUTE
ON
OFF
E-FLAT
LAST
MAX-V
TRIM
OFF
C-BAL
BASS
INPUT
80
48
10
90
01
00
C0
50
D0
41
40
A0
21
20
E0
70
F0
61
18
09
B8
29
28
E8
78
F8
69
68
C8
58
D8
49
E1
89
C9
A9
E9
71
19
59
39
79
F1
99
D9
B9
F9
08
38
30
B0
RC68+ PROGRAMMER
Permanently
attached
"A" Overlay.
A
B
C
ADJ-OFF
1
2
3
4
5
6
7
8
GLOBAL
Z-ADJ
TREBLE
VOL
MUTE
ON
OFF
E-FLAT
LAST
MAX-V
TRIM
OFF
C-BAL
BASS
INPUT
RC68+ PROGRAMMER
OFF
ON
TGL
MMT
OFF
ON
TGL
MMT
OFF
ON
TGL
MMT
OFF
ON
TGL
MMT
OFF
ON
TGL
MMT
OFF
ON
TGL
MMT
OFF
ON
TGL
MMT
OFF
ON
TGL
MMT
B
0
2
3
4
5
6
1
7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
GP-ON
GP-OFF
C
OFF
ON
TGL
MMT
OFF
ON
TGL
MMT
OFF
ON
TGL
MMT
OFF
ON
TGL
MMT
OFF
ON
TGL
MMT
OFF
ON
TGL
MMT
GP-ON
GP-OFF
D
1
3
4
5
6
2
ON
OFF
OPEN
CLOSE
ON
OFF
OPEN
CLOSE
ON
OFF
OPEN
CLOSE
ON
OFF
OPEN
CLOSE
ON
OFF
OPEN
CLOSE
ON
OFF
OPEN
CLOSE
ON
OFF
OPEN
CLOSE
ON
OFF
OPEN
CLOSE
E
1
3
4
5
6
7
8
2
1
2
3
PLAY
4
5
6
STOP
7
8
9
PAUSE
CD#
0
TR#
RESUME
DISC --
DISC +
TR --
TR +
1 CD
ALL CD
SEQL RANDOM
ARTIST
TITLE
NUMBER ZONE
LEFT
RIGHT
ENTER SELECT
F
1
3
4
5
6
7
8
2
ON/TOG
OFF
0
ON/TOG
OFF
1
ON/TOG
OFF
2
ON/TOG
OFF
3
ON/TOG
OFF
4
ON/TOG
OFF
5
ON/TOG
OFF
6
ON/TOG
OFF
7
ON/TOG
OFF
8
ON/TOG
OFF
9
ON/TOG
OFF
A
ON/TOG
OFF
B
ON/TOG
OFF
C
ON/TOG
OFF
D
ON/TOG
OFF
E
ON/TOG
OFF
F
I
Overlay
Identification
Letter
A
FIG. 2 Overlays for the RC68+ Programmer