Life Fitness CLST Manual Do Utilizador

16. Locate the L

EFT

A

CCESSORY

T

RAY

(11). Carefully slide the tray into 

the top of the L

EFT

U

PRIGHT

(1) as shown until fully seated. 

Secure the accessory tray to the L

EFT

T

OP

M

OUNTING

P

LATE

(H) 

using four S

CREWS

(21). Repeat the procedure for the R

IGHT

A

CCESSORY

T

RAY

(12) and R

IGHT

T

OP

M

OUNTING

P

LATE

(J).

17. Tighten all U

PRIGHT

B

OLTS

securely.

18. Replace the M

OTOR

C

OVER

(E) and secure the M

OTOR

C

OVER

to the F

RAME

(C) using the four previously removed S

CREWS

(D). Tighten the S

CREWS

securely. Do not overtighten the 

S

CREWS

.

19. Replace the F

RONT

G

RILL

(B) and secure the F

RONT

G

RILL

to the 

F

RAME

(C) using the four previously removed S

CREWS

(A). 

Tighten the S

CREWS

securely. Do not overtighten the S

CREWS

.

20. Locate one S

CREW

G

ROMMET

(18). Insert the S

CREW

G

ROMMET

into the square hole located above the top inside mounting bolt 
of the R

IGHT

U

PRIGHT

(2). Repeat for the remaining S

CREW

G

ROMMET

and L

EFT

U

PRIGHT

(1).

21. Locate one L

OWER

U

PRIGHT

C

OVER

(10). Position the L

OWER

U

PRIGHT

C

OVER

at the bottom notch of the R

IGHT

U

PRIGHT

(2) 

making sure the top lip of the U

PRIGHT

C

OVER

is engaged under 

the outside notch of the R

IGHT

U

PRIGHT

. Secure the U

PRIGHT

C

OVER

to the R

IGHT

U

PRIGHT

using one S

CREW

(16). Tighten the 

S

CREW

securely. Do not overtighten the S

CREW

. Repeat the pro

cedure for the L

EFT

U

PRIGHT

(1) and remaining U

PRIGHT

C

OVER

.

22. Locate the U

PRIGHT

P

LUGS

(25). Insert one U

PRIGHT

P

LUG

into 

each of the two access holes located on the lower outside of the 
L

EFT

and R

IGHT

U

PRIGHTS

(1 & 2).

23. Locate and press the H

ANDLEBAR

C

APS

(13) over the ends of the 

H

ANDLEBARS

(3). Be sure the H

ANDLEBAR

C

APS

are fully seated.

24. Using two S

CREWS

(16) each, attach the two R

EAR

F

RAME

E

ND

C

APS

(14) to the F

RAME

(C) as shown. Tighten the S

CREWS

securely. Do not overtighten the S

CREWS

.

25. The treadmill striding belt must be “walked-in” for five 

Plug the treadmill into an appropriate outlet. Turn the treadmill on
at the on/off switch. Select QUICK START from the console. 
Increase the speed to 3 mph (4.8 km/h). Start walking in the
front left corner of the walking surface and drift to the back,
move to the center of the deck and walk towards the front, and
finally walking to the right corner and drifting to the back.
Continue pattern for five minutes.

26. Refer to the specific treadmill’s Operation Manual for power 

requirements, proper line cord routing, and other critical product
information before connecting the treadmill to a power source

7