Alpine CDE-125EBT Manual Do Utilizador
25
-EN
01GB04CDE-125EBT.fm
ALPINE CDE-125EBT 68-16909Z39-A (EN)
CD Player not functioning.
• Out of operating temperature range +50°C (+120°F) for CD.
• Out of operating temperature range +50°C (+120°F) for CD.
- Allow the vehicle’s interior (or trunk) temperature to cool.
CD playback sound is wavering.
• Moisture condensation in the CD Module.
• Moisture condensation in the CD Module.
- Allow enough time for the condensation to evaporate (about 1
hour).
CD insertion not possible.
• A CD is already in the CD player.
• A CD is already in the CD player.
- Eject the CD and remove it.
• The CD is being improperly inserted.
- Make sure the CD is being inserted following instructions in
the CD Player Operation section.
Unable to fast forward or backward the CD.
• The CD has been damaged.
• The CD has been damaged.
- Eject the CD and discard it; using a damaged CD in your unit
can cause damage to the mechanism.
CD playback sound skips due to vibration.
• Improper mounting of the unit.
• Improper mounting of the unit.
- Securely re-mount the unit.
• The disc is very dirty.
- Clean the disc.
• The disc has scratches.
- Change the disc.
• The pick-up lens is dirty.
- Do not use a commercially available lens cleaner disc. Consult
your nearest Alpine dealer.
CD playback sound skips without vibration.
• The disc is dirty or scratched.
• The disc is dirty or scratched.
- Clean the disc; damaged disc should be replaced.
Error displays (built-in CD player only).
• Mechanical error.
• Mechanical error.
- Press
. After the error indication disappears, insert the disc
again. If the above-mentioned solution does not solve the
problem, consult your nearest Alpine dealer.
problem, consult your nearest Alpine dealer.
CD-R/CD-RW playback not possible.
• Close session (finalisation) has not been performed.
• Close session (finalisation) has not been performed.
- Perform finalisation and attempt playback again.
MP3 is not played back.
• Writing error occurred. The MP3 format is not compatible.
• Writing error occurred. The MP3 format is not compatible.
- Make sure the MP3 has been written in a supported format.
Refer to “About MP3” (pages 10-11), then rewrite in the
format supported by this device.
format supported by this device.
The sound is not output from the speakers.
• Unit has no output signal of the internal amplifier.
• Unit has no output signal of the internal amplifier.
- POWER IC is switched to “POW ON” (page 16).
iPod does not play and no sound is output.
• The iPod has not been recognised.
• The iPod has not been recognised.
- Reset this unit and the iPod. Refer to “Initial System Start-Up”
(page 6). To reset the iPod, refer to the Owner’s Manual of the
iPod.
iPod.
• No CD is inserted.
- Insert a CD.
• Although a disc is inserted, “NO DISC” is displayed and the unit
does not start to play or eject the disc.
- Remove the disc by following these steps:
- Remove the disc by following these steps:
Press the
button again for at least 2 seconds.
If the disc still does not eject, consult your Alpine dealer.
• Mechanism error.
1) Press the
button and eject the CD.
If not ejecting, consult your Alpine dealer.
2) When the error indication remains after ejecting, press the
button again.
If the error indication still does not turn off after pressing the
If the error indication still does not turn off after pressing the
button for a few times, consult your Alpine dealer.
• When “ERROR” is displayed:
If the disc cannot be ejected by pressing
, press the RESET switch
(refer to page 6) and press
again.
If the disc still cannot be ejected, consult your Alpine dealer.
• A sampling rate/bit rate not supported by the unit is used.
- Use a sampling rate/bit rate that is supported by the unit.
CD
MP3
Audio
iPod
Indication for CD Player
01GB00CDE-125EBT.book Page 25 Monday, September 27, 2010 10:08 AM