Insignia NS-CLIP01 Folheto

ENGLISH 11-1380

1 Press POWER/SOURCE to select iPod mode. The iPod icon appears in the 

display.

2  Plug your iPod/iPhone into the dock.

Note: The iPod/iPhone charges automatically while it is docked with your 
clock radio.

1  Dock your iPod/iPhone to the clock radio. Press        / PRESET on the clock 

radio or press Play on your iPod/iPhone.

2 Press VOL+ or VOL- to adjust the volume to a comfortable level.

3 Press TUNE         to skip to the next track forward or press TUNE         to skip 

to the next track backward. Press and hold the TUNE         or TUNE         
keys to fast forward or fast backward until you release the key.

1  Fully extend the FM antenna on the back of the clock radio.

2 Press the POWER/SOURCE button repeatedly to enter radio mode. The 

tuner frequency appears after one second.

3  Adjust the antenna to get the best radio reception.

Manual tuning:
• Press 

TUNE         or TUNE         briefly to tune to a higher or lower frequency.

Auto tuning:
•  Press and hold TUNE         or TUNE         for more than one second to 

automatically tune to a higher or lower frequency. Tuning automatically 
stops when it detects a station signal.
During auto tuning, press POWER/SOURCE to exit the auto tuning mode.

Note: If there is no station found in one cycle, auto tuning stops at the 
beginning frequency.

You can store up to ten preset stations. 

1  In radio mode, press TUNE         or TUNE         to select a station.

2  Press and hold        / PRESET for two seconds to enter programming 

mode. The PRESET (       ) icon appears and the memory digits flash in the 
display.

3 Press TUNE         or TUNE         repeatedly to select a desired preset number 

(01 to 10) to store the station.

4  Press        / PRESET to confirm your choice. The preset station is stored in 

the memory.

5  Repeat steps one through four to store more stations. Press any other 

keys to leave the programming mode.

6  To select a preset station, briefly press        / PRESET repeatedly until you 

reach the station you want.

1  Plug an audio cable with a 3.5 mm plug (not included) into the AUX IN 

jack on the back of your clock radio and into your external sound source, 
such as an MP3 player.

2  Turn on your clock radio, then press the POWER/SOURCE button 

repeatedly until AUX appears on the display.

3  Control playback from your external sound source.

•  To prevent fire or shock hazard, disconnect your clock radio from the AC 

power source when cleaning.

•  The finish on your clock radio may be cleaned with a dust cloth and cared 

for as other furniture. Use caution when cleaning and wiping the plastic 
parts.

•  If the front panel becomes dirty or smudged with fingerprints it may be 

cleaned with a soft cloth slightly dampened with a mild soap and water 
solution. Never use abrasive cloths or polishes as these will damage the 
finish of your clock radio.

Caution: 

•  Never allow water or other liquids to get inside your clock radio.

•  Modifying or tampering with the internal components of your clock radio 

can cause a malfunction and might invalidate its warranty. If your clock 
radio is not performing as it should, take it to the local dealer for assistance.

Compatible with: iPod Nano (3G/4G/5G/6G), iPod Touch (1G/2G/3G/4G), 
iPod classic, iPhone (original, 3G, 3Gs, 4,4S).

•  Number of alarms: two

•  Frequency range: FM 87.5 - 107.9 MHz (200 KHz steps)

•  Station preset: ten

•  External connections: 3.5 mm stereo, 30 pin iPod connector

•  Volume: 16 levels

•  Speaker: 2 × 36 mm

•  Output power: 1W × 2 RMS

•  Power source: DC 5.9V 1.8A adapter

•  Back-up batteries: 2 × AAA alkaline batteries

•  Dimensions (W × D × H):  6.81 × 2.87 × 5.70 in.

 

173 × 73 × 144 mm

This device complies with Part 15 of the FCC Rules. Operation of this product 
is subject to the following two conditions: (1) this device may not cause 
harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply within the limits for a 
class B digital device, pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses, and can radiate radio 
frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that 
  to which the receiver is connected.
•  Consult the dealer or an experienced technician for help.

Changes or modifications not expressly approved by the party responsible 
for compliance with the FCC Rules could void the user’s authority to operate 
this equipment.

•  Make sure that the power cord is fully inserted in the power 

outlet and firmly connected to the DC IN jack on the back.

•  Make sure that power is connected and your clock radio is 

turned on.

•  Make sure your external device is turned on and is playing.
•  Make sure the volume on your external device is turned up and 

is not set to mute.

•  Make sure that the volume on your clock radio is not extremely 

low.

• Repeatedly 

press 

the 

POWER/SOURCE button to select FM 

mode.

•  Make sure that the clock radio is correctly tuned to an FM 

station.

•  Move your clock radio closer to a window to improve reception.

•  Make sure your iPod/iPhone is on and charged.
• Repeatedly 

press 

the 

POWER/SOURCE button to select iPod 

mode.

•  Make sure your iPod/iPhone is not paused.
•  Make sure that your iPod/iPhone is properly docked.
•  Make sure that there are songs in your iPod/iPhone.
•  Make sure that the hold function is not activated on your 

iPod/iPhone .

•  Make sure that your iPod/iPhone is working properly before you 

dock it into your clock radio.

•  Remove your iPod/iPhone from the docking compartment. 

Clean the connectors in the docking compartment and on your 
iPod/iPhone, then replace it in the docking compartment.

•  Your iPod/iPhone software may be outdated. Upgrade its 

software. For details, visit www.apple.com.

•  You need to use the controls on your MP3 player to control 

playback.

•  Make sure your external device is on and charged.
• Repeatedly 

press 

the 

POWER/SOURCE button to select AUX 

mode.

•  Make sure your external device is not paused.
•  Make sure the audio cable is fully inserted into the external 

device and the AUX IN jack on the clock radio.

•  Make sure that there are songs in your external device.
•  Make sure that your external device is working properly before 

you connected it to your clock radio.

•  Make sure that your iPod/iPhone is properly docked. 
•  Make sure that the hold function is not activated on your 

iPod/iPhone.

•  Make sure that your iPod/iPhone battery is not faulty.
•  Make sure that the power cord is plugged in. 

This Class B digital apparatus complies with Canadian ICES-003.

Visit www.insigniaproducts.com for details. 

For customer service, call 1-877-467-4289
www.insigniaproducts.com

“Made for iPod” and “made for iPhone” mean that an electronic accessory has been designated to 
connect specifically to iPod, iPhone respectively, and has been certified by the developer to meet 
Apple performance standards. Apple is not responsible for the operation of this devise or its 
compliance with safety and regulatory standards. Please note that the use of this accessory with
iPod or iPhone may affect wireless performance. iPod, and iPhone are trademarks of Apple Inc. 
registered in the U.S. and other countries.

© 2012 BBY Solutions, Inc., Inc. All rights reserved. INSIGNIA is a trademark of BBY Solutions, Inc. 
Registered in some countries. All other products and brand names are trademarks of their 
respective owners.