GPX C389B Folheto

USER’S GUIDE

C389B 

Dual Alarm Clock Radio with Intelli Set™

•  CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH 

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

•  WARNING: To prevent fire or shock hazards, do not expose this

unit to rain or moisture.

•  CAUTION: Use of controls or adjustments or performance of

procedures other than those specified may result in hazardous

radiation exposure.

•  WARNING: Changes or modifications to this unit not expressly

approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

•  WARNING: Do not place the unit on top of any soft, porous, or

sensitive surfaces to avoid damaging the surface. Use a protec-

tive barrier between the unit and surface to protect the surface.

•  CAUTION: Danger of explosion if battery is incorrectly re-

placed. Replace only with the same or equivalent type.

Do not mix old and new batteries.

Do not mix alkaline, standard (carbon-zinc), or

rechargeable (ni-cad, ni-mh, etc) batteries.

Connect the included AC/DC Adpater to 

the DC Power Input on the unit and an 

AC power source to power the unit.

Requires a CR2032 battery, pre-

installed.
Use a small, Phillips-head screwdriver

to open the backup battery

compartment.

Only replace with same or equivalent

type battery.

CR2032

C389B
AC/DC adapter
Pre-installed Backup Battery (CR2032)
Documentation

When the unit is first powered on, the time will automatically be set to Eastern

Standard Time.

1.  Plug the unit into a power source.
2.  Press and hold the Clock Button.
3.  While holding the Clock Button, press the Time Zone Button repeatedly to cycle

through the available time zones.
Refer to the Time Zone Chart below to find your specific time zone.

4.  Release the Clock Button to finish setting the time.

AST

Atlantic Standard Time

UTC - 4 hours

EST

Estern Standard Time

UTC - 5 hours

CST

Central Standard Time

UTC - 6 hours

MST

Mountain Standard Time

UTC - 7 hours

PST

Pacific Standard Time

UTC - 8 hours

AKST

Alaska Standard Time

UTC - 9 hours

HAST

Hawaii-Aleutian Standard Time

UTC - 10 hours

█ SETTING THE TIME MANUALLY
1.  Plug the unit into a power source.
2.  Press and hold the Clock Button.
3.  While holding the Clock Button, press

the  Tun+/Hr Button and Tun-/Min

Button to adjust the hour and minute.

4.  Release the Clock Button to set the

adjusted time.

█ SETTING THE ALARMS
1.  With the unit powered off, press and

hold the AL 1/P- Button (Alarm 1) or

AL 2/P+ Button (Alarm 2).

2.  While holding the AL 1/P- Button or 

AL 2/P+ Button, press the Tun+/Hr

Button and Tun-/Min Button to adjust

the hour and minute.

3.  While holding the AL 1/P- Button or 

AL 2/P+ Button, press the AM/FM/

AUX Button to set the alarm to wake to

the buzzer or the AM/FM radio.
If set to AM/FM radio, the alarm will 

4.  Release the AL 1/P- Button or AL 2/P+

Button to set the adjusted alarm time.

NOTE: This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the in-

terference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.

•  Increase the separation between the equipment and

receiver.

•  Connect the equipment into an outlet on a circuit dif-

ferent from that to which the receiver is connected.

•  Consult the dealer or an experienced radio/TV techni-

cian for help.