Whirlpool WED9500T Manual Do Utilizador

Página de 28
18
To use an Automatic Cycle
NOTE: A light next to each feature will glow green when the 
feature is selected or will glow amber when the feature is 
selectable. The light will not glow when the selection is 
unavailable with the cycle or option combinations selected.
Press the POWER button.
Rotate the dial to select an Automatic Cycle.
Select DRYNESS LEVEL to adjust how dry you want the 
load to be. As the cycle runs, the control senses the 
dryness of the load and adjusts the time automatically for 
the selected Dryness Level.
NOTE: Most loads may be dried using Normal, which is 
shown in boldface type on your control panel. Normal is the 
energy preferred dryness level and will use the least energy.
The default dryness setting is Normal when an Auto Dry 
Cycle is selected. You can select a different dryness level, 
depending on your load, by pressing DRYNESS LEVEL 
and choosing More, Normal or Less. Selecting More, 
Normal or Less automatically adjusts the dryness level at 
which the dryer will shut off. Once a dryness level is set, it 
cannot be changed without stopping the cycle. 
The Dryness Level can be changed only with Automatic 
Cycles.
Press the WRINKLE SHIELD™ feature button if this 
option is desired.
Press the CYCLE SIGNAL button to set end of cycle 
signal volume to desired level.
Press the DAMP DRY CYCLE SIGNAL button to set damp 
dry signal volume to desired level.
Press and hold START button until dryer starts (about 
1 second).
Once an Automatic cycle has started, the WRINKLE 
SHIELD™ feature and cycle signals can be adjusted. Press 
the PAUSE/CANCEL key twice to clear the settings, allowing 
you to select another cycle and Dryness Level. 
NOTE: Time and Temperature are not adjustable for 
Automatic Cycles. Pressing the DRY TIME or TEMPERATURE 
buttons will cause a triple beep, indicating that the time 
cannot be changed.
How Automatic Cycles Work
The AccelerCare™ function improves drying performance 
with Auto Moisture Sensing Plus, which advances the cycle 
as moisture is extracted from clothing. A thermistor 
(electronic temperature sensor) and moisture sensing strips in 
the dryer drum help measure the amount of moisture in the 
clothes as they tumble. An electronic control determines the 
load type to help save time, avoid overdrying, and increase 
the accuracy of the end dryness level. After the first 5 minutes 
of an automatic cycle, the estimated time display will adjust 
based on the approximate load size, cycle, dryness level 
selected and amount of moisture left in the clothes. When the 
clothes have reached approximately 80% of the dryness level 
selected, the estimated time display will adjust again, 
showing the final drying time. The AccelerCare™ feature 
takes the guesswork out of drying time and enhances fabric 
care.
To use a Manual Cycle
NOTE: A light next to each feature will glow green when the 
feature is selected or will glow amber when the feature is 
selectable. The light will not glow when the selection is 
unavailable with the cycle or option combinations selected.
Press POWER.
Rotate the dial to select a Manual Cycle.
Press the DRY TIME up or down buttons until the desired 
drying time is displayed. Press DRY TIME, and the time 
will change by 1-minute intervals. Press and hold DRY 
TIME, and the time will change by 5-minute intervals. The 
initial time displayed is the actual drying time.  
The Dry Time feature can be used only with Manual 
Cycles and the Enhanced Touch Up Cycle.
Press TEMPERATURE until the desired temperature 
glows green.
Temperature settings can be changed only with Manual 
Cycles.
Press the WRINKLE SHIELD™ feature button if this 
option is desired.
Press the CYCLE SIGNAL button to set end of cycle 
signal volume to desired level.
Press and hold START button until dryer starts (about 
1 second).
NOTE: Dryness Level is not adjustable for Manual or Steam 
Cycles. Pressing the Dryness Level button will cause the 
triple beep indicating that this option is not selectable. 
While a Manual Cycle is running, you cannot change the 
cycle until you clear the settings. You can change the settings 
for Time, Temperature, the WRINKLE SHIELD™ feature and 
the cycle signals. Press the PAUSE/CANCEL key twice to 
clear the settings, allowing you to select another cycle.
To use a Steam Cycle
Press the POWER button. 
Rotate the dial to select either the Enhanced Touch Up or 
Quick Refresh cycles. 
Press the DRY TIME up or down buttons until the desired 
drying time is displayed. Press DRY TIME, and the time 
will change by 1-minute intervals. Press and hold DRY 
TIME, and the time will change by 5-minute intervals. The 
initial time displayed is the actual drying time
NOTE: The More Time and Less Time buttons can be 
used only with Manual Cycles and the Enhanced Touch 
Up Cycle.   
Press TEMPERATURE until the desired temperature 
glows green.