Panasonic DMC-TZ10 Manual Do Utilizador

Página de 178
24   
VQT2R48
VQT2R48
   25
For details about the setting procedure in the [SETUP] menu (→20)
 Using the [SETUP] menu
 
(Continued)
 
 [REC AREA]
Enables verification of 
the recordable area for 
a motion picture before 
recording.
[OFF]/[ON]
 
• Recordable area displayed for motion 
pictures should be interpreted as a 
Guideline.
 
• When using Extra Optical Zoom, the 
recordable area may not always be 
displayed for certain zoom ratios.
 
• This setting cannot be used with Intelligent 
Auto Mode.
This section is not 
recorded.
 
[ECONOMY]
Turn off the power or 
make the LCD monitor 
go dark while not using 
the camera to minimize 
battery consumption.
 [SLEEP MODE]
[OFF]/[2 MIN.]/[5 MIN.]/[10 MIN.]: 
Automatically shut off power while not in use.
 
• To restore →  Press the shutter button halfway, or turn on 
the power again.
 
• Cannot be used in the following cases:
When using AC adaptor (optional) and DC coupler 
(optional), when connected to computer/printer, during 
motion picture recording/playback, during Slide Shows, 
during automatic demo playback 
 
• Settings fixed to [5 MIN.] in [INTELLIGENT AUTO] Mode 
or [CLIPBOARD] Mode, or [10 MIN.] while Slide Show is 
paused.
 [LCD POWER SAVE]
[OFF]/[ON]:
The LCD monitor goes dark to minimize power 
consumption.
 
• Reduces the picture quality of the LCD monitor display 
during recording to minimize battery consumption 
(except for the Digital Zoom area). Note, however, that 
there is no effect on the recorded picture.
 
• When [LCD MODE] is set, the brightness of the LCD 
monitor follows the setting in [LCD MODE], but the 
picture quality of the LCD monitor stays at a low level.
Item
Settings, notes
For details about the setting procedure in the [SETUP] menu (→20)
[AUTO REVIEW]
Automatically display 
still pictures immediately 
after taking them.
[OFF]: No auto review
[1 SEC.]/[2 SEC.]:  Automatically display for 1 or 2 
seconds.
[HOLD]:  Auto review screen remains until a button (other 
than the [DISPLAY] button) is pressed
 
• Fixed to [2 SEC.] in [INTELLIGENT AUTO] Mode.
 
• In [SELF PORTRAIT], [PANORAMA ASSIST], [HI-
SPEED BURST], [FLASH BURST], and [PHOTO 
FRAME] Scene Modes, [AUTO BRACKET], [MULTI 
ASPECT], [BURST] Mode, or still pictures with audio, 
Auto Review performed regardless of setting.
 
• Motion pictures cannot be automatically reviewed.
 
 [ZOOM RESUME]
Remember the zoom 
position when turning the 
power off.
[OFF]/[ON]
 
• Cannot be set when using [SELF PORTRAIT] Scene 
Mode.
 
[NO.RESET]
Reset picture file 
numbers. 
[YES]/[NO]
 
• The folder number is updated and the file number starts 
from 0001. 
 
• A folder number between 100 and 999 can be assigned.
Numbers cannot be reset once folder number reaches 
999. In this case, save all necessary pictures to your 
computer, and format the built-in memory/card (→28).
 
• To reset folder number to 100:
First, format the built-in memory or card, and reset the 
file numbers using [NO.RESET]. Then, select [YES] on 
the folder number reset screen.
 
• File numbers and folder numbers. (→142)
Item
Settings, notes
[REC AREA] is not available in the DMC-TZ8/DMC-ZS5.