Sony DXC-D35 Manual Do Utilizador
3-7
DXC-D35/D35WS(UC)
DXC-D35P/D35WSP(CE) V1
3-3-3. Y/R-Y/B-Y CLP Level Adjustment
Equipment:
Oscilloscope
To be extended:
IF-532 board (for DXC-D35/D35P)
IF-700 board (for DXC-D35WS/D35WSP)
IF-700 board (for DXC-D35WS/D35WSP)
Preparation:
OUTPUT/DL/DCC
+ switch: BARS
Test point:
TP60, 61, 62 (GND: TP63)
/EX-490 board
/EX-490 board
Trigger:
HD (TP83/EX-490 board)
Adjustment Procedure
1.
Select “PAGE 10” of SERVICE menu, make sure that
R-Y and B-Y mode must be “ON”.
R-Y and B-Y mode must be “ON”.
2.
SERVICE menu “PAGE 6”
→
Y
CLP:
R-Y CLP:
B-Y CLP:
B-Y CLP:
3.
Adjust the following items by UP switch or DOWN
switch to meet the specification.
n
In case of Y CLP for NTSC model, perform the adjustment
In case of Y CLP for NTSC model, perform the adjustment
as follows.
1 Select “PAGE 9” of SERVICE menu, and set the
1 Select “PAGE 9” of SERVICE menu, and set the
“SETUP” to “OFF”.
2 Select “PAGE 6” of SERVICE menu, and move the
cursor to Y CLP.
3 Adjustment: A = 0
±
5 mV
4 Select “PAGE 9” of SERVICE menu, and set the
“SETUP” to “ON”.
5 And return to “PAGE 6”.
Item
Test Point
Specification
Y CLP
TP61
A = 0
±
5 mV
R-Y CLP
TP60
B = 0
±
5 mV
B-Y CLP
TP62
C = 0
±
5 mV
3-3-4. Y/SYNC/R-Y/B-Y Level Adjustment
Equipment:
Oscilloscope
To be extended:
IF-532 board (for DXC-D35/D35P)
IF-700 board (for DXC-D35WS/D35WSP)
IF-700 board (for DXC-D35WS/D35WSP)
Preparation:
OUTPUT/DL/DCC
+ switch: BARS
Test point:
TP60, 61, 62 (GND: TP63)
/EX-490 board
/EX-490 board
Trigger:
HD (TP83/EX-490 board)
Adjustment Procedure
n
Following procedures are for DXC-D35WS/D35WSP. For
Following procedures are for DXC-D35WS/D35WSP. For
DXC-D35/D35P, perform steps 2 to 4 below.
1.
Select “PAGE 9” of ADVANCE menu, set “16:9/4:3”
to “4:3”.
to “4:3”.
2.
Select “PAGE 10” of SERVICE menu, make sure that
R-Y and B-Y mode are “ON”.
3.
SERVICE menu “PAGE 5”
→
Y
LEV:
R-Y
LEV:
B-Y
LEV:
SYNC
LEV:
SETUP LEV:
n
In case of Y LEV for NTSC model, perform the adjust-
In case of Y LEV for NTSC model, perform the adjust-
ment as follows.
1 Move the cursor to Y LEV.
2 Adjust the “A” of Y LEV level.
3 Move the cursor to SETUP LEV,
1 Move the cursor to Y LEV.
2 Adjust the “A” of Y LEV level.
3 Move the cursor to SETUP LEV,
and adjust the “F” of setup level.
4 Repeat step 1 through 3 several times.
4.
Adjust by UP switch or DOWN switch.
5.
Select “PAGE 9” of ADVANCE menu, and set the
“16:9/4:3” to “4:3”.
6.
SERVICE menu “PAGE 5”
→
W Y
LEV:
W R-Y LEV:
W B-Y LEV:
7.
Adjust by UP switch or DOWN switch to meet
the specification.
the specification.
(continued)
3-3. Camera Adjustment
(PAL)
(NTSC)
A
A
B
C