Enerco HSVFB30LPT Manual Do Utilizador

Installation Instructions and Owner’s Manual

Unvented LP-Gas Vent Free Room Heaters

9.  To select the desired heat level, turn the 

temperature setting knob counterclockwise to 

between 1 & 5. 

FOR IR20LPT / IR30LPT: The thermostatic control 

used simply turns on and off the burner. 
FOR BF20LPT / BF30LPT: The thermostatic control 

used modulates the flame size as the temperature gets 

closer to set point, then it turns off the burner upon 

reaching temperature.
The burner will cycle back on when room temperature 

drops below the set temperature. The control knob can 

be set to any heat level between 1 and 5. Selecting the 

HI setting will cause the burner to remain on.

SHUTTING OFF HEATER

1.  Turn control knob clockwise to the OFF posi-

tion.

2.  Turn off all electrical power to the appliance if 

servicing is to be preformed.

3.  Turn off equipment shutoff valve.

SHUTTING OFF BURNER ONLY (PILOT STAYS LIT)

1.  Turn control knob clockwise to the PILOT/IGN 

position.

Check pilot flame pattern and burner flame pattern 

often.

Figure 21 shows a correct pilot flame pattern. Figure 

22 shows an incorrect pilot flame pattern. The incorrect 

pilot flame pattern is not touching thermocouple. This 

will cause the thermocouple to cool. When the thermo-

couple cools, the heater will shut down. If pilot flame 

pattern is incorrect, as shown in Figure 22:

•

Turn heater off (see To Turn OFF Gas to Appli-

ance, above.

 

•

See Troubleshooting, pages 14-15.

WARNING: Turn off heater and let cool before 

servicing. 
CAUTION: You must keep control areas, burner 

and circulation air passageways of heater clean. 

Inspect these areas of heater before use. Have 

the heater inspected yearly by a qualified service 

person. Heater may need more frequent cleaning 

due to excess lent from carpeting, bedding material, 

pet hair, etc. 
Make sure grille guard is in place before running 

heater. If screen or grille guard is removed for 

servicing it must be replaced prior to operating the 

heater. 

push in or turn by hand, don’t try to repair it call 

a qualified service technician or gas supplier. 

Force or attempted repair may result in a fire or 

explosion.

D.  Do not use this appliance if any part has been 

underwater. Immediately call a qualified service 

technician to inspect the appliance and to re-

place any part of the control system which has 

been underwater.

1.  STOP! Read the all safety information included 

with and on the side of heater.

2.  Make sure the equipment shutoff valve is fully 

open.

3.  Push in gas control knob and slightly turn clock-

wise to the OFF position (see figure 19).

4.  Wait five (5) minutes. Then smell for gas includ-

ing near the floor. If you smell gas, STOP! Fol-

low “B” in the safety information above. If you 

do not smell gas, go to the next step.

5.  Push in and turn control knob counterclockwise 

to PILOT. Press in control knob for five (5) sec-

onds.

Note: The first time that the heater is operated after 

connecting the gas supply, the control knob should 

be depressed for about 30 seconds. This will allow 

air to bleed from the gas system. This may take 

longer in some installations

6.  With control knob pressed in, push down and 

release the ignition button. This will light pilot. If 

needed keep pressing igniter button until pilot 

lights.

7.  Keep control knob pressed in for (30) seconds 

after lighting pilot. After 30 seconds, release 

control knob. 

•

If pilot does not stay lit, refer to Troubleshoot-

ing, pages 14 & 15. Also, contact a qualified 

service person of gas supplier for repairs. 

•

If control knob does not pop up when released, 

contact a qualified service person or gas sup-

plier for repairs.

8.

   When the pilot is lit, turn control knob coun-

terclockwise to heating level. The main burner 

should light.