Marley Engineered Products 994 Manual Do Utilizador

— 2 —

See Chart 1 for approximate weight for each model of fan. This weight factor,
coupled with the slight fan gyration that can occur during operation, requires
that a strong ceiling support be provided for attaching the hanger bracket
supplied. Refer to Fig. 1 for installation. Secure mounting bracket accordingly.

1.

Check to be sure the electrical outlet box is mounted to the ceiling
securely and that it is marked “acceptable for ceiling fan support.”
(Marley Engineered Products Model 925 Hang-Safe

TM  

Outlet Box is U.L. 

Listed for this purpose.) If the outlet box is loose, secure it.

2.

Position the slotted holes in the ball hanger bracket feet to allow the
threaded bolts of the installed Model 925 Outlet Box through them.
(See Fig. 1.) Thread the locknuts provided with the Marley Engineered 
Products Model 925 onto the threaded bolts and tighten securely. Make 
sure the ball hanger bracket is snugly and securely mounted to the outlet 
box after tightening the locknuts.

Some outlet boxes that are acceptable for fan support (other than Marley
Engineered Products Model 925) use screws to fasten the fan mounting 
bracket to them. This type of outlet box will require following these general
instructions for installation of the ball hanger bracket to the outlet box.

A.

Check to be sure the outlet box is securely mounted to the ceiling and
marked “acceptable for ceiling fan support.”

B.

Align the slotted holes in the ball hanger bracket with the fan mounting
holes in the outlet box.

C.

Secure the ball hanger bracket to the outlet box using the two screws
provided in the fan’s hardware bag.

REINFORCED OUTLET

BOX (MODEL 925 HANG

SAFE

TM 

)

NOTE: LEADS FROM FAN SHOULD PASS

THROUGH DOWNROD AS SHOWN

CEILING

MATERIAL

CONSTRUCTION

MEMBER

OUTLET BOX
HANGER BRACKET
LOCK NUTS

BALL

HANGER

BALL HANGER

DOWNROD

GROUND

WIRE

CANOPY

MOUNTING

SCREWS

BALL
HANGER
BRACKET

FIELD

SUPPLY

WIRING

1.

To reduce the risk of personal injury, use only the two steel screws (and
lock washers) provided with the fan for mounting to the outlet box.

2.

Some outlet boxes acceptable for fan support may not require the use of
these screws due to the uniqueness of their design. Consult their accom-
panying instruction sheet for ball hanger bracket installation instructions if
the above methods do not apply.

!

1. Before attaching the ceiling fan to an outlet box with a hanger bracket, be sure that the outlet box is fastened securely

to the ceiling supports.

2. Check to be sure that the outlet box is marked as “ACCEPTABLE FOR FAN SUPPORT”. (Marley Engineered Products

Model 925 HANG-SAFE

TM 

Outlet Box is U.L. Listed for this purpose. U.S. Patent Number 4,788,383.)

3. The outlet box and ceiling support should be checked to be sure that it will support at least 50 lbs. of load.
4. Electrical connections and circuit wiring should be in accordance with the National Electrical Code and/or all local codes

that may apply.

5. If you are unfamiliar with electrical circuitry, acquire the services of a qualified electrician.
6. If a light kit is to be installed to the fan, add the combined light fixture wattage to the fan wattage to determine the total

wattage rating of the installation.

7. After installation, blades must be a minimum of seven (7) feet above the floor. Do not install on ceilings less than eight

(8) feet high.

8. Do not use this product in a corrosive or explosive atmosphere.

9. The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and

situations that may occur. It must be understood that common sense, caution and care are factors which cannot be built

into any product. These factors must be supplied by the person(s) caring for and operating the unit.

!