Bionaire BSF152T Folheto

When using electrical appliances, basic safety precautions 

should always be taken including the following: 
1.  Read all instructions before using this appliance.

2.  Use fan only for purposes described in the instruction 

manual.

3.  To protect against electrical shock do not immerse 

unit, plug or cord in water or spray with liquids. Plug 

the appliance directly into a 120V AC electrical outlet.

4.  Close supervision is necessary when any appliance is 

used by or near children.

5.  Unplug from outlet when not in use, when moving 

fan from one location to another, before putting on 

or taking off parts and before cleaning.

6.  Avoid contact with moving parts.

7.  Do not operate in the presence of explosive and/or 

flammable fumes.

8.  To avoid fire hazard, NEVER place the cord under 

rugs or any parts near an open flame, cooking or 

other heating appliance.

9.  Do not operate any appliance with a damaged cord 

or plug after the appliance malfunctions, or has been 

dropped/damaged in any manner. Discard fan or 

return to an authorized service facility for 

examination and/or repair.

10. The use of attachments not recommended or sold by 

the appliance manufacturer may cause hazards.

11. Do not use outdoors.

12. Do not let the cord hang over the edge of a table, 

counter or come in contact with hot surfaces or leave 

exposed to high traffic areas.

13. To disconnect, grip plug and pull from wall outlet. 

Never yank on cord.

14. Always use on a dry, level surface.

15. Do not operate fan until fully assembled with all 

parts properly in place.

16. This product is intended for household use ONLY and 

not for commercial or industrial applications.

17. WARNING: To reduce the risk of electrical shock 

injury to persons, do not use in window.

18. WARNING: This fan is provided with an internal 

electronic fan speed control. To reduce the risk of fire 

or electric shock, do not use this fan with any other 

solid-state speed control device.

Assembly Time: 5-10 Minutes
NOTE: Check all packaging materials and make sure 

that you have all of the parts necessary for assembling 

your fan.
1.   Insert the threaded end of the Lower Pole into the 

Base. Refer to Figure 2.

2.   Secure the Base Weight to the threaded end of the 

Lower Pole with the Base Weight Nut. Refer to Figure 2.

3.   Insert the threaded end of the Upper Pole into the 

Lower Pole. Twist clockwise to lock. Refer to Figure 3.

4.   Slide Neck of the Motor Housing over the Upper Pole 

and secure by tightening the Thumb Screw.

5.   Secure the Rear Grill to the Motor Housing by 

tightening the Rear Grill Mounting Nut. Refer to 

Figure 4 for the correct positioning of the Rear Grill 

to the Motor Housing.

6.   Secure the Fan Blade to the Motor Shaft by 

tightening the Fan Blade Cap. Refer to Figure 5.

7.   Secure the Front Grill to the Rear Grill by snapping 

the Front Grill into the clips around the perimeter of 

the Rear Grill.

1.  Set fan on a dry, level surface.

2.  Plug cord into any standard 120 volt AC outlet.

3.  The speed/mode is adjustable by pushing the Mode/

Off (   ) button either from the fan housing or the 

remote control.

To turn the oscillation feature off pull the Oscillation 

Control Knob (

) all the way up. To turn the 

oscillation feature on push the Oscillation Control Knob    

(

) all the way down.

Potential for Radio/Television interference 
This product has been tested and found to comply with 

the limits for a Class B digital device, pursuant to part 15 

of the FCC rules.
These limits are designed to provide reasonable 

protection against harmful interference in a residential 

installation. The product generates, uses, and can radiate 

radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful 

interference to radio communications. However, there is 

no guarantee that the interference will not occur in a 

particular installation. If the product does cause harmful 

interference to radio or television reception, which can be 

determined by turning the product on or off, the user is 

encouraged to try to correct the interference by one or 

more of the following measures: 
•   Reorient or relocate the receiving antenna.

•   Increase the separation between the product and the 

receiver.

•   Connect the product into an outlet on a circuit 

different from that to which the receiver is 

connected.

•   Consult the dealer or an experienced radio/TV 

technician for help.

Changes or modifications not expressly approved by the 

party responsible for compliance could void the user’s 

authority to operate the equipment. 

This unit includes two (2) AAA batteries. 
Battery Replacement 
a)   Locate the battery cover on the back of the remote 

control handset. Slide the battery cover off with your 

thumb. 

b)   Use the tip of a pen to loosen each battery. Hold the 

remote control handset at an angle to allow the 

batteries to slide out. 

c)   Insert two new batteries, pressing them firmly into 

their slot.

d)   Replace the battery cover. 
NOTES: 
•   Do not mix old and new batteries.

•   Do not mix alkaline, standard (carbon-zinc), or 

rechargeable (nickel-cadmium) batteries.

•   Replace all batteries of a set at the same time.

•   Clean the battery contacts and the devices’ contacts 

prior to installing the batteries.

•   Remove the batteries from the equipment when it is 

not being used for an extended period of time.

•   Remove the used batteries promptly.

Figure 2

M

K

Figure 6

Figure 4

F

E

Figure 5

C

D

Figure 3

I

K

A.   Logo Plate 

B.   Front Grill 

C.   Fan Blade Cap 

D.   Fan Blade 

E.   Rear Grill Mounting Nut 

F.   Rear Grill 

G.    Motor Shaft 

H.    Motor Housing

I.    Upper Pole  

J.    Grill Clips (6) 

K.    Lower Pole 

L.    Decorative Cap 

M.    Base 

N.    Base Weight 

O.    Base Weight Nut 

P.    Oscillation Control Knob 

Q.    Tilt-Adjustment Knob 

R.  

Thumb 

Screw 

S. 

  Mode/Off  button

T. 

   IR  Lens

A

B

C

D

E

F

G

H

I

L

Q

M

R

Figure 1

P

K

N

O

BSF152T-U_08EM1.indd   2

BSF152T-U_08EM1.indd   2

12/22/08   3:49:39 PM

12/22/08   3:49:39 PM