Louisville Tin and Stove W505F Manual Do Utilizador

1”

11”

2”

A)

The wall furnace should be located near the center of
the house for best heat distribution.

B)

Due to high temperatures, the appliance should be
located out of traffic and away from furniture and
draperies.

C)

Children and adults should be alerted to the hazards
of high surface temperature and should stay away to
avoid burns or clothing ignition.

D)

Young children should be carefully supervised when
they are in the same room as the appliance.

E)

Do not place clothing or other flammable material on
or near the appliance.  Precautions should be taken
so as not to place furniture, drapes, or other articles
directly in front of grille or lower access door that
would obstruct air openings as proper air flow is
critical to proper operation of unit.

F)

Any safety screen guard or casing front removed for
servicing an appliance must be replaced prior to
operating the appliance.

G)

If the area where the appliance is to be installed
contains carpeting, tile or combustible materials, other
than wood flooring, the appliance shall be installed
on a metal plate, a wood panel or other non-
combustible materials.  The use of ceramic or quarry
tile is acceptable and will provide a surface that is
easily cleaned.  This material is to extend the full width
and depth of the appliance.

As viewed from front of heater, the minimum clearance

from cabinet to combustible construction:  Side Wall – 1”;
 Floor – 2”; Ceiling – 11”.

w.c. on Natural Gas and 10” w.c. on L.P. Gas.  The
maximum inlet pressure in the gas supply pipe should
never exceed 14” w.c. on L.P. Gas or 7.0” w.c. on
Natural Gas.

The appliance and its individual shutoff valve

must be disconnected from the gas supply piping system
during any pressure testing of that system at test
pressures in excess of  ½ psig.

The appliance must be isolated from the gas

supply piping system by closing its individual manual
shutoff valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than ½
psig.

The minimum inlet pressure in the gas supply

pipe should be 5.0” w.c. on Natural Gas or 11” w.c. on
L.P. Gas, “for purpose of input adjustment”.

The appliance is orificed at the factory for

elevations up to 2,000 feet.  If installed above 2,000 feet,
the BTU input must be reduced 4% per 1,000 feet.  See
the following orifice chart for the proper orifice for a
specific elevation.  A blank orifice is shipped in the high
altitude kit with each heater.  This orifice(s) will have to
be drilled to correct size by installer, gas supplier or
qualified serviceman.

Model

0  to

     2,000 -     4,000 -        6,000 -          8,000 –

No.          2,000’           4,000’      6,000’         8,000’         10,000’

W255F      43               44              45               47               48

W355F      36               38              40               41               43
        ORDER KIT #49820  45-1 HIGH ALTITUDE KIT

W505F      43               44              45               47               48
       ORDER KIT #49850  2287-2 HIGH ALTITUDE KIT

Model

0 to

2,000 -

   4,000 -      6,000 -          8,000 –

No.         2,000’       4,000’        6,000’        8,000’         10,000’

W256F      1.45mm    54               54               55              55

W356F      52              52              52               53              54
       ORDER KIT #49820   45-1 HIGH ALTITUDE KIT

W506F      1.45mm     54               54              55              55
       ORDER KIT #49850   2287-2 HIGH ALTITUDE KIT

Page 3

In selecting a location for installation it is necessary

to provide adequate accessibility clearances for servicing
and proper operation.  This appliance must not be connected
to a chimney flue that serves to vent a solid-fuel burning
(wood or coal) appliance, or a multi-vent system.

All controls are preassembled at the factory.

The normal manifold pressure should be 3.5”