Majestic Appliances 3379 Manual Do Utilizador
10
Vermont Castings Radiance Vent-Free Gas Heater
20004555
Install Optional Fan
It is easiest to install the optional fan kit #2767/FK26,
before the stove is moved to its final location or con-
nected to the gas line.
before the stove is moved to its final location or con-
nected to the gas line.
The fan consists of a blower assembly and a rheostat
switch that are connected by a wire harness. The
blower attaches to a bracket at the bottom of the rear
shroud. The rheostat installs at the bottom of the stove
on the left of the valve.
switch that are connected by a wire harness. The
blower attaches to a bracket at the bottom of the rear
shroud. The rheostat installs at the bottom of the stove
on the left of the valve.
The fan kit includes a ‘snapstat’, a temperature-sensing
switch which will be mounted to the blower duct just
below the top plate of the stove. The snapstat automati-
cally turns the fan on or off at approximately 109
switch which will be mounted to the blower duct just
below the top plate of the stove. The snapstat automati-
cally turns the fan on or off at approximately 109
°
F.
The rheostat provides a range of fan speed settings
from OFF (which overrides the snapstat function) to
high.
from OFF (which overrides the snapstat function) to
high.
Kit Contents
• Fan assembly with rheostat and snapstat
• wire tie
• control knob
• retaining collar
CAUTION: Sheet metal edges can be sharp. Be sure
to wear protective gloves.
to wear protective gloves.
1. Loosen the four phillips head screws which secure
the rear shroud to the stove sides. (Fig. 9)
the rear shroud to the stove sides. (Fig. 9)
2. Carefully pull the shroud assembly away from the
rear of the stove.
rear of the stove.
3. With the rear shroud assembly in the upright posi-
tion, set the bottom of the shroud on a padded surface
to prevent scratching the surface. Unfasten the four
phillips head screws which attach the outer shroud to
the inner duct assembly.
tion, set the bottom of the shroud on a padded surface
to prevent scratching the surface. Unfasten the four
phillips head screws which attach the outer shroud to
the inner duct assembly.
Assemble the Legs
1. Slide stove to the rear of the pallet just far enough to
access rear leg holes. Make sure the stove does not
tip over backwards. (Fig. 7)
tip over backwards. (Fig. 7)
ST720
Fig. 7 Slide stove back just far enough to access rear leg
holes.
holes.
2. Attach the rear legs using 3/8” hex head bolts and
flat washer supplied. Tighten with a 9/16” wrench or
socket.
socket.
3. Carefully tip the stove onto its rear legs. Adjust the
pallet to allow access to one of the front leg holes.
Be sure to leave the pallet under the stove to prevent
the stove from falling fully forward. (Fig. 8)
Be sure to leave the pallet under the stove to prevent
the stove from falling fully forward. (Fig. 8)
CAUTION: To prevent valve tubing from being
crushed or damaged, make sure to rest valve on
wooden pallet.
crushed or damaged, make sure to rest valve on
wooden pallet.
Washer
Hex Head Bolt
ST721
Fig. 8 Carefully tip stove onto back legs. Leave pallet under
stove to keep stove from falling fully forward.
stove to keep stove from falling fully forward.
4. Have your assistant attach one leg using the hard-
ware described.
5. Move the pallet to allow access to the other front leg
hole. Attach remaining leg.
6. Remove pallet and allow stove to gently rest on all
four legs.
7. Adjust leg levelers to compensate for irregularities in
the hearth.
ST189
Fig. 9 Loosen four phillips screws holding rear shroud
assembly and remove. Remove four phillips screws holding
rear shroud to inner duct assembly. Remove rear shroud.
assembly and remove. Remove four phillips screws holding
rear shroud to inner duct assembly. Remove rear shroud.
Rear Shroud
Assembly
Assembly