Hampton Direct H25-NG1 Manual Do Utilizador
28
Hampton
®
H25-1 Direct Vent Freestanding Gas Stove
INSTALLATION
CONVERSION KIT #434-969 FROM NG TO LP
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !!
Each Kit contains one LPG
Conversion Kit and one DC
Sparker Kit.
Conversion Kit and one DC
Sparker Kit.
LPG Conversion Kit Contains:
Qty. Part #
Qty. Part #
Description
1
904-163
Burner Orifi ce #54
1
918-590
Decal "Converted to
LPG"
1
908-528
Red "LPG" label
1 904-529
5/32"
Allen
Key
1 910-037
LPG Injector
(Pilot
Orifi
ce)
1 918-480
Instruction
Sheet
DC Sparker Kit Contains:
Qty. Part #
Qty. Part #
Description
1
820-475
Bracket DC Sparker
1
820-476
Bracket DC Sparker
1
904-153
Washer #8 External Star
1 904-330
Nut
8-32
Hex
1
904-438
Plug Nylon 0.750 Hole,
Black
1
904-531
Bushing Split Plastic
0.500
in.
1
904-543
Screw 8-32 x 3/4 Pan
Head
2
904-553
Screw #8 x 1/2 Type
"B",
Black
Oxide
1 910-073
Spark
Generator
Battery
Holder
1
910-074
Spark Generator
Switch
C/W
Wire
1
910-078
Battery Size AA
Energizer
En91
2 910-199
Clip
Wire
Holder
1
910-903
Wire Fan To Power Cord
Ground
30
in.
904-781
Velcro
Hook,
Black
904-782
Velcro
Hook,
Black
Remove the 2 screws, push Burner
Assembly to the left and lift out.
3) Pull off the pilot cap to expose the pilot
orifi
orifi
ce.
Installation of the LPG
Conversion Kit:
Conversion Kit:
1)
Shut off the gas supply.
2) P33-4
Only:
a) Remove the louvers (and bay door if it
is installed).
b) Open the fl ush door and remove the
door.
c) Remove the logs, embers, and brick
panels (if used).
2) H25-1
Only:
a) Lift off the Cast Top and remove
the glass front (refer to Glass
Replacement section in the H25-1
manual) and carefully remove the
logs and lava rock (refer to Log
Installation section in manual).
Replacement section in the H25-1
manual) and carefully remove the
logs and lava rock (refer to Log
Installation section in manual).
b) Remove burner by removing the 2
screws on each side and then lifting
the burner tray out.
the burner tray out.
Pilot assembly is now accessible for
steps 4) to 9).
d) Remove the 2 screws holding the
Burner Assembly to the fi rebox base.
Push the Burner Assembly to the left
and lift out.
Push the Burner Assembly to the left
and lift out.
Screws
4)
Unscrew the pilot orifi ce with the Allen
key and replace with the LPG pilot orifi ce
in the kit and replace pilot cap.
key and replace with the LPG pilot orifi ce
in the kit and replace pilot cap.
5)
Remove burner orifi ce with a 1/2"
wrench and discard. Use another
wrench to hold on to the elbow behind
wrench and discard. Use another
wrench to hold on to the elbow behind
the orifi ce.
Burner Orifi ce
6)
Reinstall new burner orifi ce LPG
stamped #54 and tighten.
stamped #54 and tighten.
Note: Use a magnetic type
screwdriver if possible.