Hampton Direct H15-NG1 Manual Do Utilizador

6

Hampton

®

 H15-1 Direct Vent Freestanding Gas Stove

The  Direct Vent Freestanding Gas Stove must 
be installed in accordance with these instruc-
tions. Carefully read all the instructions in this 
manual fi rst. Consult the building authority 
having jurisdiction to determine the need for a 
permit prior to starting the installation.

H15-NG1 is approved for use with 
natural gas.

 

H15-LP1 is approved for use with liq-
uefi ed petroleum gases (propane).

Electrical:  120V  A.C. system.

Optional Circulation Fan:  
 Variable 

speed, 

125/75.

Log Sets:  Ceramic fi bre, 4 per set.

Vent System: Coaxial (6-5/8" outer / 4" inner 
liner) rigid fl ue and termination cap.

This Hampton

®

 product has been tested and 

listed by ITS Testing Services as a Direct Vent 
Room Heater to the following standards:  
CGA-2.17-M91, and ANSI Z21.88B-2003/CSA 
2.33B-2003.

This Direct Vent System Appliance must be 
installed in accordance with the manufacturer's 
installation instructions and the Manufactured 
Home Construction and Safety Standard, Title 
24 CFR, Part 3280, or the current Standard of 
Fire Safety Criteria for Manufactured Home In-
stallations, Sites, and Communities ANSI/NFPA 
501A, and with CAN/CSA Z240-MH Mobile 
Home Standard in Canada.

This appliance installation must comply with the 
manufacturer's installation instructions and local 
codes, if any. In the absence of local codes fol-
low the current National Fuel Gas Code, ANSI 
Z223.1 and the current National Electrical Code 
ANSI/NFPA 70 in the U.S.A., and the current 
CAN/CGA B149 Gas Installation Code and the 
current Canadian Electrical Code CSA C22.1 
in Canada.

This Hampton

®

 Mobile/Manufactured Home 

Listed appliance comes factory equipped 
with a means to secure the unit.

This Hampton

®

 Mobile/Manufactured 

Home listed appliance comes equipped 
with a dedicated #8 ground lug to which 
an 18 gauge copper wire from the steel 
chassis ground must be attached.

Safe installation and operation of this appli-
ance requires common sense, however, we 
are required by the Canadian Safety Standards 
and ANSI Standards to make you aware of the 
following:

1)  Provide adequate clearances for servicing, 

proper operation and around the air openings 
into the combustion chamber. 

2)  The appliance must be installed on a fl at, 

solid, continuous surface (e.g. wood, metal, 
concrete). This may be the fl oor, or it can be 
raised up on a platform to enhance its visual 
impact. The appliance may be installed on 
carpeting, tile, wood fl ooring or other com-
bustible material, because the appliance's 
base extends the full width and depth of the 
appliance. The  Direct Vent Freestanding 
Gas Stove can be installed in a wide variety 
of ways and will fi t nearly any room layout. 
It may be installed in a recessed position, 
framed out into the room, or across a cor-
ner.

3)  The  Direct Vent Freestanding Gas Stove  is 

approved for alcove installations, which meet 
the clearances listed in the "Clearance to 
Combustibles" section.  This unit is approved 
for manufactured home installations, see 
the "Manufactured Mobile Home Additional 
Requirements" and "Rigid Pipe Venting 
Systems" sections for the required vent ar-
rangements. If installed into a manufactured 
home the unit must be bolted down to the 
fl oor. 

4)  This appliance is Listed for bedroom  instal-

lations when used with a Listed Millivolt 
Thermostat. Some areas may have further 
requirements, check local codes before 
installation.

5)  This appliance is Listed for Alcove installa-

tions, maintain minimum Alcove clearances 
as follows,  minimum width of  32-1/2"